Jeep Wrangler (2018 year). Manual — part 18
description in “Switchable Automatic Locking Retractors
(ALR)” under “Occupant Restraint Systems” for additional
information on ALR.
Please see the table below and the following sections for
more information.
Lap/Shoulder Belt Systems For Installing Child
Restraints In This Vehicle
Automatic Locking Retractor Locations (Two-Door Models)
ALR = Switchable Automatic Locking Retractor
Top Tether Anchorage Symbol
Automatic Locking Retractor Locations (Four-Door
Models)
ALR = Switchable Automatic Locking Retractor
Top Tether Anchorage Symbol
278
SAFETY
Frequently Asked Questions About Installing Child Restraints With Seat Belts
What is the weight limit (child’s
weight + weight of the child re-
straint) for using the Tether Anchor
with the seat belt to attach a forward
facing child restraint?
Weight limit of the Child Restraint
Always use the tether anchor when
using the seat belt to install a for-
ward facing child restraint, up to the
recommended weight limit of the
child restraint.
Can the rear-facing child restraint
touch the back of the front passenger
seat?
Yes
Contact between the front passenger
seat and the child restraint is al-
lowed, if the child restraint manufac-
turer also allows contact.
Can the head restraints be removed?
Two Door Models — No
Four Door Models — Yes
Two Door — None
Four Door — Center Only
Can the buckle stalk be twisted to
tighten the seat belt against the belt
path of the child restraint?
No
Do not twist the buckle stalk in a
seating position with an ALR retrac-
tor.
NOTE:
If the folding, non-adjustable head restraint inter-
feres with the installation of the child restraint, the head
restraint may be folded and the child seat installed in front
of it (Two-Door Models).
WARNING!
Always make sure the head restraint is in its upright
position when the seat is to be used by an occupant
who is not in a child restraint. Sitting in a seat with the
head restraint in its lowered position could result in
serious injury or death in a collision.
5
SAFETY
279
Installing A Child Restraint With A Switchable
Automatic Locking Retractor (ALR):
Child restraint systems are designed to be secured in
vehicle seats by lap belts or the lap belt portion of a
lap/shoulder belt.
WARNING!
• Improper installation or failure to properly secure a
child restraint can lead to failure of the restraint. The
child could be badly injured or killed.
• Follow the child restraint manufacturer’s directions
exactly when installing an infant or child restraint.
1. Place the child seat in the center of the seating position.
For some second row seats, you may need to recline the
seat and/or raise the head restraint to get a better fit. If
the rear seat can be moved forward and rearward in the
vehicle, you may wish to move it to its rear-most
position to make room for the child seat. You may also
move the front seat forward to allow more room for the
child seat.
2. Pull enough of the seat belt webbing from the retractor
to pass it through the belt path of the child restraint. Do
not twist the belt webbing in the belt path.
3. Slide the latch plate into the buckle until you hear a
“click.”
4. Pull on the webbing to make the lap portion tight
against the child seat.
Car Seat With Head Restraint Folded
1 — Folded Headrest
2 — Child Restraint
280
SAFETY
5. To lock the seat belt, pull down on the shoulder part of
the belt until you have pulled all the seat belt webbing
out of the retractor. Then, allow the webbing to retract
back into the retractor. As the webbing retracts, you will
hear a clicking sound. This means the seat belt is now in
the Automatic Locking mode.
6. Try to pull the webbing out of the retractor. If it is
locked, you should not be able to pull out any webbing.
If the retractor is not locked, repeat step 5.
7. Finally, pull up on any excess webbing to tighten the lap
portion around the child restraint while you push the
child restraint rearward and downward into the vehicle
seat.
8. If the child restraint has a top tether strap and the
seating position has a top tether anchorage, connect the
tether strap to the anchorage and tighten the tether
strap. See the section “Installing Child Restraints Using
the Top Tether Anchorage” for directions to attach a
tether anchor.
9. Test that the child restraint is installed tightly by pulling
back and forth on the child seat at the belt path. It
should not move more than 1 inch (25.4 mm) in any
direction.
Any seat belt system will loosen with time, so check the
belt occasionally, and pull it tight if necessary.
Installing Child Restraints Using The Top Tether
Anchorage
WARNING!
Do not attach a tether strap for a rear-facing car seat to
any location in front of the car seat, including the seat
frame or a tether anchorage. Only attach the tether
strap of a rear-facing car seat to the tether anchorage
that is approved for that seating position, located
behind the top of the vehicle seat. See the section
“Lower Anchors and Tethers for CHildren (LATCH)
Restraint System” for the location of approved tether
anchorages in your vehicle.
5
SAFETY
281
1. Look behind the seating position where you plan to
install the child restraint to find the tether anchorage.
You may need to move the seat forward to provide
better access to the tether anchorage. If there is no top
tether anchorage for that seating position, move the
child restraint to another position in the vehicle if one is
available.
2. Route the tether strap to provide the most direct path for
the strap between the anchor and the child seat. If your
vehicle is equipped with adjustable rear head restraints,
raise the head restraint, and where possible, route the
tether strap under the head restraint and between the
two posts. If not possible, lower the head restraint and
pass the tether strap around the outboard side of the
head restraint.
Tether Strap Mounting (Two-Door Models)
282
SAFETY
3. Attach the tether strap hook of the child restraint to the
top tether anchorage as shown in the diagram.
4. Remove slack in the tether strap according to the child
restraint manufacturer’s instructions.
WARNING!
• An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchorage position directly be-
hind the child seat to secure a child restraint top
tether strap.
• If your vehicle is equipped with a split rear seat,
make sure the tether strap does not slip into the
opening between the seatbacks as you remove slack
in the strap.
Center Tether Attachment — Four-Door Without
Center Armrest
1. Lower the adjustable center head restraint to the full
down position.
2. Route the tether strap over the seatback and head
restraint.
Tether Strap Mounting (Four-Door Models With Center
Armrest)
5
SAFETY
283
3. Attach the tether strap hook of the child restraint to the
center tether anchorage located on the back of the seat.
4. Remove slack in the tether strap according to the child
restraint manufacturer’s instructions.
Transporting Pets
Air Bags deploying in the front seat could harm your pet.
An unrestrained pet will be thrown about and possibly
injured, or injure a passenger during panic braking or in a
collision.
Pets should be restrained in the rear seat in pet harnesses or
pet carriers that are secured by seat belts.
SAFETY TIPS
Transporting Passengers
NEVER TRANSPORT PASSENGERS IN THE CARGO
AREA.
WARNING!
• Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.
• It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision, people
riding in these areas are more likely to be seriously
injured or killed.
• Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat belts.
• Be sure everyone in your vehicle is in a seat and
using a seat belt properly.
(Continued)
Tether Strap Mounting (Four-Door Models Without Center
Armrest)
284
SAFETY
Exhaust Gas
WARNING!
Exhaust gases can injure or kill. They contain carbon
monoxide (CO), which is colorless and odorless.
Breathing it can make you unconscious and can even-
tually poison you. To avoid breathing (CO), follow
these safety tips:
• Do not run the engine in a closed garage or in
confined areas any longer than needed to move your
vehicle in or out of the area.
• If you are required to drive with the trunk/liftgate/
rear doors open, make sure that all windows are
closed and the climate control BLOWER switch is set
at high speed. DO NOT use the recirculation mode.
• If it is necessary to sit in a parked vehicle with the
engine running, adjust your heating or cooling con-
trols to force outside air into the vehicle. Set the
blower at high speed.
The best protection against carbon monoxide entry into the
vehicle body is a properly maintained engine exhaust
system.
Whenever a change is noticed in the sound of the exhaust
system, when exhaust fumes can be detected inside the
vehicle, or when the underside or rear of the vehicle is
damaged, have a competent mechanic inspect the complete
exhaust system and adjacent body areas for broken, dam-
aged, deteriorated, or mispositioned parts. Open seams or
loose connections could permit exhaust fumes to seep into
the passenger compartment. In addition, inspect the ex-
haust system each time the vehicle is raised for lubrication
or oil change. Replace as required.
Safety Checks You Should Make Inside The Vehicle
Seat Belts
Inspect the seat belt system periodically, checking for cuts,
frays, and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the system.
Front seat belt assemblies must be replaced after a collision.
Rear seat belt assemblies must be replaced after a collision
if they have been damaged (i.e., bent retractor, torn web-
bing, etc.). If there is any question regarding seat belt or
retractor condition, replace the seat belt.
Air Bag Warning Light
The Air Bag warning light
will turn on for four to
eight seconds as a bulb check when the ignition switch
is first turned to ON/RUN. If the light is either not on
during starting, stays on, or turns on while driving,
5
SAFETY
285
have the system inspected at an authorized dealer as
soon as possible. This light will illuminate with a single
chime when a fault with the Air Bag Warning Light has
been detected, it will stay on until the fault is removed.
If the light comes on intermittently or remains on while
driving, have an authorized dealer service the vehicle
immediately. Refer to “Occupant Restraint Systems” in
“Safety” for further information.
Defroster
Check operation by selecting the defrost mode and place
the blower control on high speed. You should be able to
feel the air directed against the windshield. See your
authorized dealer for service if your defroster is inoper-
able.
Floor Mat Safety Information
Always use floor mats designed to fit your vehicle. Only
use a floor mat that does not interfere with the operation of
the pedal assemblies. Only use a floor mat that is securely
attached using the floor mat fasteners so it cannot slip out
of position and interfere with the pedal assemblies or
impair safe operation of your vehicle in other ways.
WARNING!
An improperly attached, damaged, folded, or stacked
floor mat, or damaged floor mat fasteners may cause
your floor mat to interfere with the accelerator, brake,
or clutch pedals and cause a loss of vehicle control. To
prevent SERIOUS INJURY or DEATH:
• ALWAYS securely attach
your floor mat using the
floor mat fasteners. DO NOT install your floor mat
upside down or turn your floor mat over. Lightly pull
to confirm mat is secured using the floor mat fasten-
ers on a regular basis.
• ALWAYS REMOVE THE EXISTING FLOOR MAT
FROM THE VEHICLE
before installing any other
floor mat. NEVER install or stack an additional floor
mat on top of an existing floor mat.
• ONLY install floor mats designed to fit your vehicle.
NEVER install a floor mat that cannot be properly
attached and secured to your vehicle. If a floor mat
needs to be replaced, only use a FCA approved floor
mat for the specific make, model, and year of your
vehicle.
(Continued)
286
SAFETY
WARNING! (Continued)
• ONLY use the driver’s side floor mat on the driver’s
side floor area. To check for interference, with the
vehicle properly parked with the engine off, fully
depress the accelerator, the brake, and the clutch
pedal (if present) to check for interference. If your
floor mat interferes with the operation of any pedal,
or is not secure to the floor, remove the floor mat
from the vehicle and place the floor mat in your
trunk.
• ONLY use the passenger’s side floor mat on the
passenger’s side floor area.
• ALWAYS make sure objects cannot fall or slide into
the driver’s side floor area when the vehicle is
moving. Objects can become trapped under accelera-
tor, brake, or clutch pedals and could cause a loss of
vehicle control.
• NEVER place any objects under the floor mat (e.g.,
towels, keys, etc.). These objects could change the
position of the floor mat and may cause interference
with the accelerator, brake, or clutch pedals.
(Continued)
WARNING! (Continued)
• If the vehicle carpet has been removed and re-
installed, always properly attach carpet to the floor
and check the floor mat fasteners are secure to the
vehicle carpet. Fully depress each pedal to check for
interference with the accelerator, brake, or clutch
pedals then re-install the floor mats.
• It is recommended to only use mild soap and water
to clean your floor mats. After cleaning, always check
your floor mat has been properly installed and is
secured to your vehicle using the floor mat fasteners
by lightly pulling mat.
Periodic Safety Checks You Should Make Outside
The Vehicle
Tires
Examine tires for excessive tread wear and uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread or sidewall. Inspect the tread for cuts
and cracks. Inspect sidewalls for cuts, cracks, and bulges.
Check the wheel nuts for tightness. Check the tires (includ-
ing spare) for proper cold inflation pressure.
5
SAFETY
287
Lights
Have someone observe the operation of brake lights and
exterior lights while you work the controls. Check turn
signal and high beam indicator lights on the instrument
panel.
Door Latches
Check for proper closing, latching, and locking.
Fluid Leaks
Check area under vehicle after overnight parking for fuel,
coolant, oil, or other fluid leaks. Also, if gasoline fumes are
detected or if fuel, or brake fluid leaks are suspected. The
cause should be located and corrected immediately.
288
SAFETY
STARTING AND OPERATING
CONTENTS
䡵 STARTING THE ENGINE . . . . . . . . . . . . . . . . . .292
▫ Manual Transmission — If Equipped . . . . . . . .292
▫ Automatic Transmission — If Equipped . . . . . .292
▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . . .292
▫ Extreme Cold Weather
(Below –22°F Or −30°C) . . . . . . . . . . . . . . . . . .296
▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . .296
▫ After Starting. . . . . . . . . . . . . . . . . . . . . . . . . .296
䡵 ENGINE BLOCK HEATER — IF EQUIPPED . . . .297
䡵 ENGINE BREAK-IN RECOMMENDATIONS . . . .297
䡵 PARKING BRAKE . . . . . . . . . . . . . . . . . . . . . . .298
䡵 MANUAL TRANSMISSION — IF EQUIPPED . . .299
▫ Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300
▫ Downshifting. . . . . . . . . . . . . . . . . . . . . . . . . .301
IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . .303
▫ Ignition Park Interlock . . . . . . . . . . . . . . . . . . .304
▫ Brake/Transmission Shift Interlock System . . . .304
▫ Eight–Speed Automatic Transmission . . . . . . . .304
䡵 FOUR–WHEEL DRIVE OPERATION . . . . . . . . . .312
▫ Four-Position Transfer Case . . . . . . . . . . . . . . .312
▫ Five-Position Transfer Case . . . . . . . . . . . . . . .315
▫ Trac-Lok Rear Axle — If Equipped . . . . . . . . . .319
▫ Axle Lock (Tru-Lok) — Rubicon Models . . . . . .319
▫ Electronic Sway Bar Disconnect —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .320
䡵 ELECTRO-HYDRAULIC POWER STEERING . . . .322
䡵 STOP/START SYSTEM — AUTOMATIC
TRANSMISSION (IF EQUIPPED) . . . . . . . . . . . .323
6
▫ Automatic Mode . . . . . . . . . . . . . . . . . . . . . . .323
▫ Possible Reasons The Engine Does Not
Autostop . . . . . . . . . . . . . . . . . . . . . . . . . . . .323
▫ To Start The Engine While In Autostop Mode . .324
▫ To Manually Turn Off The Stop/Start System . .325
▫ To Manually Turn On The Stop/Start System . . .326
▫ System Malfunction . . . . . . . . . . . . . . . . . . . . .326
TRANSMISSION (IF EQUIPPED) . . . . . . . . . . . .326
▫ Automatic Mode . . . . . . . . . . . . . . . . . . . . . . .326
▫ Possible Reasons The Engine Does Not
Autostop . . . . . . . . . . . . . . . . . . . . . . . . . . . . .327
▫ To Start The Engine While In Autostop Mode . . .327
▫ To Manually Turn Off The Start/Stop System . . .328
▫ To Manually Turn On The Stop/Start System . . .329
▫ System Malfunction . . . . . . . . . . . . . . . . . . . . .329
䡵 SPEED CONTROL — IF EQUIPPED . . . . . . . . . .329
▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . .330
▫ To Set A Desired Speed. . . . . . . . . . . . . . . . . . .330
▫ To Vary The Speed Setting . . . . . . . . . . . . . . . .330
▫ To Accelerate For Passing . . . . . . . . . . . . . . . . .331
▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . .331
▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . .332
䡵 PARKSENSE REAR PARK ASSIST —
IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . .332
▫ ParkSense Sensors . . . . . . . . . . . . . . . . . . . . . .333
▫ ParkSense Warning Display. . . . . . . . . . . . . . . .333
▫ ParkSense Display . . . . . . . . . . . . . . . . . . . . . .334
▫ Enabling And Disabling ParkSense . . . . . . . . . .338
▫ Service The ParkSense Rear Park Assist System. .338
▫ Cleaning The ParkSense System. . . . . . . . . . . . .339
▫ ParkSense System Usage Precautions . . . . . . . . .339
䡵 PARKVIEW REAR BACK UP CAMERA . . . . . . . .341
䡵 REFUELING THE VEHICLE . . . . . . . . . . . . . . . .342
▫ Fuel Filler Cap . . . . . . . . . . . . . . . . . . . . . . . .342
290
STARTING AND OPERATING
▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . .344
䡵 VEHICLE LOADING . . . . . . . . . . . . . . . . . . . . .344
▫ Certification Label . . . . . . . . . . . . . . . . . . . . . .344
䡵 TRAILER TOWING . . . . . . . . . . . . . . . . . . . . . .346
▫ Common Towing Definitions. . . . . . . . . . . . . . .346
▫ Trailer Hitch Classification . . . . . . . . . . . . . . . .348
▫ Trailer Towing Weights (Maximum Trailer Weight
Ratings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .349
▫ Trailer And Tongue Weight . . . . . . . . . . . . . . .350
▫ Towing Tips. . . . . . . . . . . . . . . . . . . . . . . . . . .352
MOTORHOME, ETC.) . . . . . . . . . . . . . . . . . . . .354
▫ Towing This Vehicle Behind Another Vehicle. . . .354
▫ Recreational Towing — Four-Wheel Drive
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .355
䡵 DRIVING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . .357
▫ On-Road Driving Tips . . . . . . . . . . . . . . . . . . .357
▫ Off-Road Driving Tips . . . . . . . . . . . . . . . . . . .358
6
STARTING AND OPERATING
291
STARTING THE ENGINE
Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belts.
WARNING!
• When exiting the vehicle, always remove the key fob
from the ignition and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or others
could be seriously or fatally injured. Children
should be warned not to touch the parking brake,
brake pedal or the gear selector.
• Do not leave the key fob in or near the vehicle, or in
a location accessible to children. A child could oper-
ate power windows, other controls, or move the
vehicle.
• Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.
Manual Transmission — If Equipped
Apply the parking brake, place the gear selector in NEU-
TRAL, and press the clutch pedal before starting the
vehicle. This vehicle is equipped with a clutch interlocking
ignition system. It will not start unless the clutch pedal is
pressed to the floor.
Four-Wheel Drive Models Only
In 4L mode, this vehicle will start regardless of whether or
not the clutch pedal is pressed to the floor. This feature
enhances off-road performance by allowing the vehicle to
start when in 4L without having to press the clutch pedal.
The “4WD Low Indicator Light” will illuminate when the
transfer case has been shifted into this mode.
Automatic Transmission — If Equipped
Start the vehicle with the gear selector in the PARK
position (vehicle can also be started in NEUTRAL). Apply
the brake before shifting to any driving range.
Normal Starting
To Turn On The Engine Using The ENGINE START/
STOP Button
1. The transmission must be in PARK or NEUTRAL.
292
STARTING AND OPERATING
2. Press and hold the brake pedal while pushing the
ENGINE START/STOP button once.
3. The system takes over and attempts to start the vehicle.
If the vehicle fails to start, the starter will disengage
automatically after 10 seconds.
4. If you wish to stop the cranking of the engine prior to
the engine starting, push the button again.
NOTE:
Normal starting of either a cold or a warm engine
is obtained without pumping or pressing the accelerator
pedal.
To Turn Off The Engine Using ENGINE START/STOP
Button
1. Place the gear selector in PARK, then push and release
the ENGINE START/STOP button.
2. The ignition will return to the OFF mode.
3. If the gear selector is not in PARK (with vehicle stopped)
and the ENGINE START/STOP button is pushed once,
the transmission will automatically select PARK and the
engine will turn off, however the ignition will remain in
the ACC mode (NOT the OFF mode). Never leave a
vehicle out of the PARK position, or it could roll.
4. If the gear selector is in NEUTRAL, and the vehicle
speed is below 5 mph (8 km/h), pushing the START/
STOP button once will turn the engine off. The ignition
will remain in the ACC mode.
5. If the vehicle speed is above 5 mph (8 km/h), the
ENGINE START/STOP button must be held for two
seconds (or three short pushes in a row) to turn the
engine off. The ignition will remain in the ACC mode
(NOT the OFF mode) if the engine is turned off when
the transmission is not in PARK.
NOTE:
The system will automatically time out and the
ignition will cycle to the OFF mode after 30 minutes of
inactivity if the ignition is left in the ACC or RUN (engine
not running) mode and the transmission is in PARK.
ENGINE START/STOP Button Functions — With Driv-
er’s Foot OFF The Brake Pedal (In PARK Or NEUTRAL
Position)
The ENGINE START/STOP button operates similar to an
ignition switch. It has three modes: OFF, ACC, and RUN.
To change the ignition modes without starting the vehicle
and use the accessories, follow these steps:
1. Starting with the ignition in the OFF mode,
6
STARTING AND OPERATING
293
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст