Jeep Wrangler (2018 year). Manual — part 7
4. Set the rear door frame pin into the hole on top of the
body side, just behind the rear door opening.
5. Carefully position the top of the door frame onto the
rear of the front door rail, making sure rubber seals lay
flat. Ensure the seals are installed correctly to avoid
water leaks.
Step Four
Position Of Frame Above Door
1 — Front Door Rail
2 — Rear Door Frame
102
GETTING TO KNOW YOUR VEHICLE
6. Swing the frame bracket around the side of the rail, and
insert the screws from underneath. Tighten with #40
Torx head driver until they are snug, being careful not to
cross-thread the screws or overtighten.
Door Frame Installation Two Door Models — If
Equipped
1. Carefully place the front door rail in the rubber seal at
the top of the windshield, and line up the holes for the
Torx head screws (two for each door).
2. Swing the frame bracket around the side of the rail, and
insert the screws from underneath. Tighten with #40
Torx head driver until they are snug, being careful not to
cross-thread the screws or overtighten.
CAUTION!
Do not overtighten the screws. You can strip the screws
if they are overtightened.
Step Six
Step Two
3
GETTING TO KNOW YOUR VEHICLE
103
SOFT TOP TWO DOOR MODELS — IF EQUIPPED
WARNING!
• Do not drive the vehicle with the rear window
up/removed unless the quarter windows are also
removed. Dangerous exhaust gases could enter the
vehicle causing harm to the driver and passengers.
• The fabric quarter windows and fabric top are de-
signed only for protection against the elements. Do
not rely on them to contain occupants within the
vehicle or to protect against injury during an acci-
dent. Remember, always wear seat belts.
• Make sure hands and fingers are clear of all pinch
points when installing and removing the soft tops.
The lift assist mechanism and side bows may cause
serious injury if fingers or hands get caught in
between.
CAUTION!
The soft top is not designed to carry any additional
loads such as roof racks, spare tires, building, hunting,
or camping supplies, and/or luggage, etc. Also, it was
not designed as a structural member of the vehicle and,
thus, cannot properly carry any additional loads other
than environmental (rain, snow, etc.).
If the temperature is below 72°F (24°C) and/or the top has
been folded down for a period of time, the top will appear
to have shrunk when you raise it, making it difficult to put
up. This is caused by a natural contraction of the vinyl
coating on the fabric top.
Place the vehicle in a warm area. Pull steadily on the top
fabric. The vinyl will stretch back to its original size and the
top can then be installed. If the temperature is 41°F (5°C)
or below, do not attempt to put the top down or roll the
rear or side curtains.
104
GETTING TO KNOW YOUR VEHICLE
CAUTION!
• Do not run a fabric top through an automatic car
wash. Window scratches and wax build up may
result.
• Do not lower the top when the temperature is below
41°F (5°C). Damage to the top may result.
• Do not move your vehicle until the top has been
either fully attached to the windshield frame, or fully
lowered.
• Do not lower the top with the windows installed.
Window and top damage may occur.
• Refer to “Appearance Care For Fabric Top Models”
in “Bodywork” in “Servicing And Maintenance” for
further information. It contains important informa-
tion on cleaning and caring for your vehicle’s fabric
top.
(Continued)
CAUTION! (Continued)
• Do not use any tools (screwdrivers, etc.) to pry or
force any of the clamps, clips, or retainers securing
the soft top. Do not force or pry the soft top frame-
work when opening or closing. Damage to the top
may result.
Failure to follow these cautions may cause interior
water damage, stains or mildew on the top material:
• It is recommended that the top be free of water prior
to opening it. Operating the top, opening a door or
lowering a window while the top is wet may allow
water to drip into the vehicle’s interior.
• Careless handling and storage of the soft top may
damage the seals, causing water to leak into the
vehicle’s interior.
• The soft top must be positioned properly to ensure
sealing. Improper installation can cause water to leak
into the vehicle’s interior.
3
GETTING TO KNOW YOUR VEHICLE
105
Lowering The Soft Top
Side View Top And Components
1 — #1 Bow
6 — #6 Bow
2 — #2 Bow
7 — Rear Quarter Window
3 — #3 Bow
8 — Lower Window Retainer
4 — #4 Bow
9 — Front Window Retainer
5 — #5 Bow
106
GETTING TO KNOW YOUR VEHICLE
Rear View Top And Components
1 — Rear Window Retainer Attachment Points
2 — Quarter Window Pillars
3 — Swing Gate Bar Retainers
3
GETTING TO KNOW YOUR VEHICLE
107
NOTE:
The rear window and rear quarter windows must
be removed before lowering the soft top to prevent damage
to the top. Clean the side and rear windows before removal
to assist in preventing scratching during removal of the
soft top. If the plastic retainers are difficult to operate due
to road dust, etc., clean them with a mild soap solution and
a small brush. Cleaning products are available through an
authorized dealer.
Remove The Rear Window:
1. With the swing gate open, remove the rear window’s
plastic retainers from the lower right and left corners.
2. Grasp the swing gate bar, rotate it outward and upward
releasing it from both the right and left retainers.
Step One
Step Two (Left Side Shown)
108
GETTING TO KNOW YOUR VEHICLE
3. While holding the window in place, slide the tailgate bar
to the left separating it from the rear window. Store in
soft window bag, or a safe location.
4. Remove the plastic retainers from both quarter window
pillars.
Step Three
Step Four
3
GETTING TO KNOW YOUR VEHICLE
109
5. While keeping the rear window level, slide to the left
until it is completely separate from its retainer. Do not
pull downward while removing the rear window.
Damage to the retainer could result.
Remove The Right And Left Quarter Windows:
1. Through the rear opening, push the bottom corner
outward and release tab from the bottom of the window
pillar.
Step Five
Step One
110
GETTING TO KNOW YOUR VEHICLE
2. Starting at the rear of the vehicle, remove plastic retainer
from along the bottom of the window moving toward
the front of the vehicle.
3. Remove plastic retainer from bottom to top of the
window.
Step Two
Step Three
3
GETTING TO KNOW YOUR VEHICLE
111
4. While keeping the window level, slide rearward until it
is completely separate from its retainer. Do not pull
downward while removing the window. Damage to
the retainer could result.
5. Store in soft window bag or a safe location.
Lowering The Soft Top Into Sunrider Position
1. After removing the rear window and quarter panel
windows, move to the front of the vehicle.
2. Fold both sun visors forward against the windshield.
3. Release the header latches from the crossbar by pulling
the handle downward. Make sure the hook is disen-
gaged from its receiver.
Step Four
Step Three
112
GETTING TO KNOW YOUR VEHICLE
4. From both the driver and passenger sides, lift up on the
#1 Bow of the soft top to start the operation.
5. Move to the side of the vehicle and use the side link to
fold the soft top rearward into the Sunrider position.
NOTE:
If leaving the soft top in the Sunrider position,
secure the top by using the two velcro straps provided in
the center console.
Step Four
Secured Top When In Sunrider Position
3
GETTING TO KNOW YOUR VEHICLE
113
Lowering The Soft Top Into Fully Lowered Position
1. From the Sunrider position, remove straps if previously
secured and move to the rear of the vehicle.
2. Locate the Sunrider latch beneath the #6 Bow of the soft
top on the driver’s side.
3. Pull the latch downward to release the top, and allow
the soft top to slide rearward freely in the guide tracks
to the stowed position.
Sunrider Latch Beneath #6 Bow
Step Three
114
GETTING TO KNOW YOUR VEHICLE
4. While pushing downward slightly on the folded soft
top, slide the lock lever on the driver and passenger side
lift assist mechanisms to the “lock” position.
5. Once the lock is in the “lock” position, push downward
on each side of the folded soft top to ensure it is secure.
An audible “click” may be heard.
Step Four
Lock Position
3
GETTING TO KNOW YOUR VEHICLE
115
Raising The Soft Top
Raising The Soft Top From The Fully Lowered Position
1. While pushing down on the rear of the top, slide the
lock lever on the driver and passenger side Lift Assist
Mechanisms to the “unlock” position.
Push Down While Unlocking
Unlocked Position
116
GETTING TO KNOW YOUR VEHICLE
2. Push up and forward from the #5 Bow along the guide
track until it locks into the Sunrider position with an
audible “click”.
3. Gently pull rearward on the #6 Bow to ensure the top is
locked in the Sunrider position.
4. Using the side link, lift and push the soft top toward the
front of the vehicle guiding the top into the closed
position.
Step Two
Lower Top Into Closed Position
3
GETTING TO KNOW YOUR VEHICLE
117
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст