Jeep Renegade (2018 year). Manual — part 12
Important
Apply the plate in a highly visible point
of the vehicle, near the mounting pipe or
inside the luggage compartment.
To ensure correct operation of the
system, periodically remove all deposits
of dirt which may have accumulated on
the ball head bar and from the mounting
pipe. The lock must only be treated with
graphite.
Periodically lubricate the joints, the
sliding surfaces and the balls with grease
without resin or oil. Lubrication is also a
further corrosion protection.
if the vehicle is washed with
high-pressure jets, the ball head bar
must be removed and the dedicated plug
fitted. The ball head bar must never be
treated with high-pressure jets.
Two keys are supplied together with the
removable ball tow bar. Note down the
four-digit key number and keep it in a
safe place. This number is to be used for
ordering any duplicate keys that may be
required.
IMPORTANT To install a tow hook
contact a Jeep Dealership.
WARNING
148) The ABS with which the car is
equipped will not control the braking
system of the trailer. Particular caution is
required on slippery roads.
149) Never modify the braking system of
the vehicle to control the trailer brake.
The trailer braking system must be fully
independent of the car’s hydraulic system.
189
IN AN EMERGENCY
A punctured tyre or a burnt-out bulb?
At times, a problem may interfere with
our journey.
The pages on emergencies can help you
to deal with critical situations
independently and with calm.
In an emergency we recommend that you
call the freephone number found in the
Warranty Booklet.
It is also possible to call the national or
international universal freephone number
to search for the nearest Dealership.
HAZARD WARNING LIGHTS. . . . . .192
CHANGING A BULB. . . . . . . . . . .193
REPLACING FUSES . . . . . . . . . . .202
CHANGING A WHEEL . . . . . . . . .209
TIREKIT . . . . . . . . . . . . . . . . . .215
JUMP STARTING. . . . . . . . . . . . .218
FUEL CUT-OFF SYSTEM . . . . . . . .220
AUTOMATIC TRANSMISSION GEAR
LEVER UNLOCKING . . . . . . . . . .220
TWIN CLUTCH AUTOMATIC
TRANSMISSION LEVER UNLOCK . .222
BROKEN-DOWN VEHICLE TOWING .224
TOWING THE VEHICLE . . . . . . . . .225
191
HAZARD WARNING
LIGHTS
CONTROL
Press the button fig. 141 to switch the
lights on/off.
When the hazard warning lights are on,
the
and
warning lights flash.
IMPORTANT The use of hazard
warning lights is governed by the
highway code of the country you are
driving in: comply with legal
requirements.
Emergency braking
In the event of emergency braking the
hazard warning lights switch on
automatically as well as warning lights
and
in the instrument panel.
The lights switch off automatically when
emergency braking ceases.
141
J0A0954C
192
IN
AN
EMERGENCY
CHANGING A BULB
150) 151) 152) 153)
76)
GENERAL INSTRUCTIONS
Before replacing a bulb check the
contacts for oxidation;
replace blown bulbs with others of the
same type and power;
after replacing a headlight bulb,
always check its alignment;
when a light is not working, check
that the corresponding fuse is intact
before replacing the bulb. For the
location of fuses, refer to the paragraph
“If a fuse blows” in this chapter.
IMPORTANT When the weather is cold
or damp or after heavy rain or washing,
the surface of headlights or rear lights
may steam up and/or form drops of
condensation on the inside. This is a
natural phenomenon due to the
difference in temperature and
humidity between the inside and the
outside of the glass which does not
indicate a fault and does not
compromise the normal operation of
lighting devices. The mist disappears
quickly when the lights are turned on,
starting from the centre of the diffuser,
extending progressively towards the
edges.
193
Light bulbs
Type
Power
Front position/Daytime running lights (D.R.L.)
P21/5W
21/5W
Rear side/brake light
P21W
21 W
Low/high beams (halogen)
H4
60/55W
Main beam/dipped beam headlights (Xenon gas discharge)
D5S
25 W
Front direction indicators
PY21W
21 W
Rear direction indicators
W16W
16 W
Side directional indicators (front and on the external rear voew mirror)
WY5W
5 W
3rd stop
LED
–
Number plate
W5W
5 W
Fog lights
H11
55 W
Rear fog light
W16W
16 W
Reversing light
W16W
16 W
194
IN
AN
EMERGENCY
Light bulbs
Type
Power
Front ceiling light
C5W
5 W
Front ceiling light (shade flaps)
C5W
5 W
Rear ceiling light (versions without sun roof)
C5W
5 W
Rear ceiling lights (versions with openable roof)
C5W
5 W
Luggage compartment light
W5W
5 W
Glove compartment light
W5W
4 W
195
REPLACING AN EXTERNAL BULB
Front upper light group (halogen high/low
beams)
To replace the bulb, proceed as follows:
working from inside the engine
compartment, remove cover A fig. 142,
using the dedicated tab;
turn the bulb and bulb holder
assembly B fig. 143 anticlockwise and
then remove it sliding it outwards;
remove, sliding it outwards, the bulb
and bulb holder assembly C fig. 144,
disconnecting it from connector D;
install the new bulb and bulb holder
assembly, ensuring that it is locked
correctly;
then insert the bulb and bulb holder
assembly in its housing and turn it
clockwise, making sure that it is locked
correctly.
Front upper light group (Xenon gas emitting
high/low beams)
For this replacement, please refer to the
Jeep Assistance network.
Front lower light cluster
Parking light/daytime running lights
(D.R.L.) and front directional indicators
To replace the bulbs, proceed as follows:
steer the wheels completely;
using the screwdriver, undo screws A
fig. 145 and remove flap B;
142
J0A0260C
143
J0A0261C
144
J0A0414C
196
IN
AN
EMERGENCY
remove electrical connectors C
fig. 146;
turn anticlockwise (on the left device)
or clockwise (on the right device) and
remove the bulb and bulb holder
assemblies fig. 147: D = side
lights/daytime running lights (DRLs), E =
direction indicators;
replace the burnt bulb: to extract it,
press lightly on it (1 fig. 148 ) and at the
same time turn it counter-clockwise (2);
insert the new bulb, by pressing it
fig. 148 and turning it clockwise, making
sure that it locks correctly;
then insert the bulb and bulb holder
assemblies in their respective housings
and turn them anticlockwise (right side)
and clockwise (left side), ensuring that
they are locked correctly;
reconnect the electrical connectors;
finally, refit flap B fig. 145, fully
tightening fixing screws A.
Front fog lights
To replace the bulbs, proceed as follows:
steer the wheels completely;
using the screwdriver, undo screws A
fig. 149 and remove flap B;
145
J0A0211C
146
J0A0306C
147
J0A0263C
148
J0A0264C
197
using tab C fig. 150, remove electrical
connector D;
turn the light bulb and holder E
fig. 150 counter-clockwise and replace
the bulb;
insert the new bulb and holder group,
making sure it is properly blocked;
reconnect the electrical connection;
finally replace flap B fig. 149,
screwing down the attachment screws A
completely.
Side turn light
Side direction indicators on door mirrors
(where provided)
For light bulb replacement, please refer
to Jeep Assistance Network.
Rear upper light group
This contains the parking lights, brake
lights and directional indicators.
To replace the bulbs, proceed as follows:
open the tailgate;
with the point indicated with an
arrows, remove flap A fig. 151;
unscrew fixing device B fig. 152;
disconnect the electrical connector,
working on device C;
149
J0A0211C
150
J0A0301C
151
J0A0637C
198
IN
AN
EMERGENCY
remove the rear light group,
unscrewing towards the outside as shown
in fig. 153;
undo the four fixing screws D
fig. 154 and remove the bulb holder
unit;
replace the bulb involved (fig. 155:
E/G = brake lights, F = directional
indicators) (bulbs E and G always light
up at the same time);
fit the new bulb, making sure it is
correctly locked;
correctly remount the bulb holder
group for the rear light group, screwing
the four attaching crews tightly;
reposition the rear light cluster on the
car;
screw the attachment device for the
rear light group tightly and reconnect the
electrical connections;
refit flap A fig. 151, ensuring that it
locks correctly;
finally, close the tailgate.
152
J0A0296C
153
J0A0316C
154
J0A0268C
155
J0A0270C
199
Rear lower light cluster
These contain the rear fog light bulbs
(left side) and reversing light bulbs (right
side).
To replace the bulbs, proceed as follows:
using the screwdriver, unscrew screws
A fig. 156 and B and remove flap C;
upper screw A is easy to access,
whereas for lower screw B it is necessary
to incline the blade of the screwdriver
appropriately as illustrated in fig. 157;
turn bulb holder D
fig. 158 anticlockwise and replace the
bulb concerned;
fit the new bulb, making sure it is
correctly locked;
refit the bulb holder in its housing and
turn it clockwise, making sure that it
locks correctly;
refit flap C correctly, completely
tightening the screws.
3
rd
brake lights
The 3
rd
brake lights are LED-based. To
replace them, contact a Jeep Dealership.
Number plate lights
To replace the bulbs, proceed as follows:
remove lenses A fig. 159;
turn the bulb holder clockwise and
remove the bulb;
156
J0A0212C
157
J0A0213C
158
J0A0302C
200
IN
AN
EMERGENCY
insert the new bulb, making sure it is
properly blocked in the holder;
finally, refit the lenses.
WARNING
150) Before replacing the bulb, wait for
the exhaust ducts to cool down: DANGER
OF SCALDING!
151) Modifications or repairs to the
electric system that are not carried out
properly or do not take the system
technical specifications into account can
cause malfunctions leading to the risk of
fire.
152) Halogen bulbs contain pressurised
gas, in the case of breakage they may
burst causing glass fragments to be
projected outwards.
IMPORTANT
76) Halogen bulbs must be handled
holding the metallic part only. Touching
the transparent part of the bulb with your
fingers may reduce the intensity of the
emitted light and even reduce the lifespan
of the bulb. In the event of accidental
contact, wipe the bulb with a cloth
moistened with alcohol and let the bulb
dry.
159
J0A0444C
201
153) Only replace the light bulbs when the
engine is off and in a position that does
not interfere with traffic and lets you
safely replace them (see the description in
the “Replacement” paragraph). Also
ensure that the engine is cold, to prevent
the risk of burns.
REPLACING FUSES
INTRODUCTION
154) 155) 156) 157) 158)
77) 78)
Fuse extracting pliers
To replace a fuse, use the pliers hooked
to the engine compartment fuse box
cover (see fig. 160 ).
Grab the pliers from the upper tabs, as
shown in fig. 161, press them and
extract the pliers pulling upwards.
The pliers have two different ends,
specifically designed (see fig. 162 ) to
remove the different types of fuse
present in the vehicle:
A: MINI fuse;
B: J-CASE fuse.
FUSE LOCATION
Fuses are grouped together in four
fuseboxes located in the engine
compartment, under the dashboard and
inside the boot.
160
J0A0250C
161
J0A0331C
162
J0A0686C
202
IN
AN
EMERGENCY
LPG versions
The LPG system components are
protected by specific fuses. Contact a
Jeep Dealership for replacement.
ENGINE COMPARTMENT FUSE
BOX
The fuse box is located by the side of the
battery fig. 163.
Releasing fixing screw and removing fuse
box cover
Proceed as follows:
fully tighten screw A fig. 164, using
the dedicated screwdriver provided;
slowly rotate the screw anticlockwise,
until resistance is encountered (do not
overtighten);
slowly release the screw;
opening is indicated by the entire
screw head coming out of its housing;
remove cover B fig. 164, sliding it
completely upwards, as indicated in the
figure.
The number identifying the electrical
component corresponding to each fuse is
shown on the cover. After replacing a
fuse, make sure that you have closed
cover B correctly.
163
J0A0117C
164
J0A0116C
203
Fitting fuse box cover and locking screw
Proceed as follows:
fix cover B fig. 164 to the box
correctly, sliding it down completely from
the top;
fully tighten screw A fig. 164, using
the dedicated screwdriver provided;
slowly rotate the screw clockwise,
until resistance is encountered (do not
overtighten);
slowly release the screw;
closure is indicated by the securing of
the entire screw head in its housing.
DASHBOARD FUSE BOX
The fuse box fig. 165 is located near the
left side of the steering column and the
fuses can be accessed easily from the
lower part of the dashboard.
For fuse replacement, contact a Jeep
Dealership.
LUGGAGE COMPARTMENT FUSE
BOX
To access the fuses use device A
fig. 166 and subsequently remove flap B.
165
J0A0114C
166
J0A0295C
204
IN
AN
EMERGENCY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст