Kia Sedona (2008 year). Instruction — part 49
Fig. 2: Locating Passenger Air Bag Module Mounting Bolts
Courtesy of KIA MOTORS AMERICA, INC.
4. Remove the crash pad. Refer to CRASH PAD .
5. Remove the heater duct from the crash pad.
Fig. 3: Identifying Heater Duct
Courtesy of KIA MOTORS AMERICA, INC.
6. Remove the mounting nuts from the crash pad. Then remove the passenger airbag.
NOTE:
Replace the crash pad which is damaged while PAB is deployed.
CAUTION: The removed airbag module should be stored In a clean, dry place
with the airbag cushion up.
2008 Kia Sedona EX
2008 RESTRAINTS Air Bag Module (Passenger Side) - Sedona
Microsoft
Monday, May 24, 2010 3:53:08 PM
Page 2
© 2006 Mitchell Repair Information Company, LLC.
Fig. 4: Identifying Crash Pad Mounting Nuts
Courtesy of KIA MOTORS AMERICA, INC.
INSTALLATION
1. Disconnect the negative (-) cable from battery and wait for at least three minutes.
2. Remove ignition key from the vehicle.
3. Place a Passenger Airbag (PAB) on the crash pad and tighten the Passenger Airbag (PAB) mounting nuts.
Tightening Torque:
0.7-0.8 kgf.m (7.0-8.0 N.m, 5.2-5.9 lb. ft)
4. Install the heater duct to the crash pad.
5. Install the crash pad. Refer to CRASH PAD .
6. Tighten the PAB mounting bolts.
Tightening Torque:
1.2-1.3 kgf.m (12.0-13.0 N.m, 8.9-9.6 lb. ft)
7. Connect the Passenger Airbag (PAB) harness connector to the SRS main harness connector.
8. Reinstall the glove box. Refer to GLOVE BOX REPLACEMENT .
9. Reconnect the battery negative cable.
10. After installing the Passenger Airbag (PAB), confirm proper system operation:
Turn the ignition switch ON; the SRS indicator light should be turned on for about 6 seconds and
then go off.
2008 Kia Sedona EX
2008 RESTRAINTS Air Bag Module (Passenger Side) - Sedona
Microsoft
Monday, May 24, 2010 3:53:08 PM
Page 3
© 2006 Mitchell Repair Information Company, LLC.
2008 RESTRAINTS
Troubleshooting (Airbag) - Sedona
DESCRIPTION
HI-SCAN CHECK
1. Turn the ignition switch off.
2. Connect the Hi-Scan Pro connector to the data link connector located under the crash pad.
Fig. 1: Connecting Hi-Scan Pro Connector To Data Link Connector
3. Turn the ignition switch on and power on the Hi-Scan Pro.
4. Read DTCs.
5. Find and repair the trouble, and clear the DTCs using Hi-Scan Pro.
6. Disconnect the Hi-Scan Pro.
DIAGNOSTIC TROUBLESHOOTING FLOW
2008 Kia Sedona EX
2008 RESTRAINTS Troubleshooting (Airbag) - Sedona
2008 Kia Sedona EX
2008 RESTRAINTS Troubleshooting (Airbag) - Sedona
Microsoft
Monday, May 24, 2010 3:55:00 PM
Page 1
© 2006 Mitchell Repair Information Company, LLC.
Microsoft
Monday, May 24, 2010 3:55:06 PM
Page 1
© 2006 Mitchell Repair Information Company, LLC.
Fig. 2: Diagnostic Troubleshooting Flow Chart
TERMINAL & CONNECTOR INSPECTION
Be sure to perform "TERMINAL & CONNECTOR INSPECTION" before doing "INSPECTION
PROCEDURE" for troubleshooting of each DTC.
1. Visually inspect all connectors related to the affected circuit for damage and secure connection.
2. Inspect terminals for damage and corrosion.
3. Are any problems found?
NO
Go to next step (INSPECTION PROCEDURE).
YES
After repairing the trouble part, check whether DTC occurs or not.
CAUTION: Avoid damaging connectors during the inspection process.
2008 Kia Sedona EX
2008 RESTRAINTS Troubleshooting (Airbag) - Sedona
Microsoft
Monday, May 24, 2010 3:55:01 PM
Page 2
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст