Kia Sedona (2008 year). Instruction — part 159
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1102.
DTC B1613 LOST COMMUNICATION WITH CLU, BUS FAILURE
COMPONENT LOCATION
Fig. 83: Locating IPM & Cluster Connector
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
Refer to DTC B1602.
DTC DESCRIPTION
The ECM sets DTC B1613 if Cluster module haven't transmitted DATA for 10sec in normal CAN
communicating.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
Item
Detecting Condition
Possible Cause
DTC Strategy
-
Faulty IPM
Open/short in Cluster module power harness
Faulty Cluster module
Poor connection of connected part
Enable Conditions
-
Threshold value
-
Detecting time
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 105
© 2006 Mitchell Repair Information Company, LLC.
3. Select "Diagnostic Trouble Codes (DTC s)" mode and monitor "DTC Status" parameter.
4. Is the DTC B1613 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
Refer to DTC B1102.
SIGNAL CIRCUIT INSPECTION
Refer to DTC B1605.
POWER SUPPLY CIRCUIT INSPECTION
1. Check for open or short in power harness
1. Ignition "OFF".
2. Connect Cluster module
3. Measure voltage value between terminal "M04-2-7" of FAM and chassis ground.
Specification: 9-16V
Fig. 84: Measuring Voltage Value Between Terminal M04-2-7 Of FAM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 106
© 2006 Mitchell Repair Information Company, LLC.
YES
Go to "COMPONENT INSPECTION" procedure.
NO
Check for open or short in power harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
COMPONENT INSPECTION
1. Check Cluster module
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Substitute with a known-good Cluster module and Check if the DTC is erased.
4. Is the DTC erased?
YES
Substitute with a known-good Cluster module and check for proper operation.
If the problem is corrected, replace Cluster module and then go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
NO
Go to step 2.
2. Check IPM
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Substitute with a known-good IPM and Check if the DTC is erased.
4. Is the DTC erased?
YES
Substitute with a known-good IPM and check for proper operation.
If the problem is corrected, replace IPM and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
NO
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage.
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 107
© 2006 Mitchell Repair Information Company, LLC.
Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE REPAIR"
procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1102.
DTC B1624 EEPROM FAILURE
COMPONENT LOCATION
Fig. 85: Locating IPM
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
IPM is a component of BCM that consists of DDM, ADM, FAM, RAM, IMS and cluster module. Each
component of BCM controls relative unit and share information by CAN communication line. IPM is
abbreviation of Instrument Panel Module. it is located at the lower part of steering column and controls front
area electronic unit.
DTC DESCRIPTION
The ECM sets DTC B1624 if there's any fault in writing/reading IPM EEPROM data procedure.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
Item
Detecting Condition
Possible Cause
DTC Strategy
-
Faulty IPM
Enable Conditions
IGN: ON, ENG: OFF
Threshold value
-
Detecting time
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 108
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст