Kia Sedona (2008 year). Instruction — part 219
COMPONENT INSPECTION
1. Check Rear blower switch illumination
1. Ignition "ON" & engine "OFF"
2. Disconnect Rear blower switch illumination
3. Measure the resistance between both terminals of Rear blower switch illumination light bulb.
Specification: approx. 0.04 ohms
(If light bulb fails, infinity ohms is measured.)
Fig. 300: Measuring Resistance Between Both Terminals Of Stop Lamp Light Bulb
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within the specification?
YES
Go to step 2.
NO
Replacing the light bulb with `light bulb for test', if normal operating condition is confirmed,
Replace `light bulb for test' with `new light bulb' and go to "VERIFICATION OF VEHICLE
REPAIR".
2. Check RAM
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Check if DTC is erased after replacing RAM with "RAM for test".
4. Is the DTC erased?
YES
Replace "RAM for test" with "new RAM" and go to "VERIFICATION OF VEHICLE
REPAIR".
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:22 PM
Page 345
© 2006 Mitchell Repair Information Company, LLC.
NO
Check connecting condition of connector and go to "VERIFICATION OF VEHICLE REPAIR".
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B2115 REAR DEFOG RELAY FAILURE.
DTC B2599 REAR BLOWER SWITCH ILLUMINATION SHORT TO GROUND
COMPONENT LOCATION
Refer to DTC B2598.
GENERAL DESCRIPTION
Refer to DTC B2598.
DTC DESCRIPTION
B2599 is set when short to ground in rear blower switch illumination circuit is detected.
DTC DETECTING CONDITION
Refer to DTC B2535.
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF" & RAM: "ON"
3. Select "Diagnostic Trouble Codes (DTCs)" mode and monitor "DTC Status" parameter
4. Is the DTC B2599 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
Refer to DTC B2441.
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:22 PM
Page 346
© 2006 Mitchell Repair Information Company, LLC.
POWER SUPPLY CIRCUIT INSPECTION
1. Check short in power circuit
1. Ignition "ON" & engine "OFF"
2. Disconnect Rear blower switch illumination.
3. Measure the resistance between Rear blower switch illumination power circuit connector terminal
at RAM side (BCM-RR1-13) and chassis ground.
Specification: infinity ohms
Fig. 301: Measuring Resistance Between Illumination Power Circuit Connector Terminal
(BCM-RR1-13) And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within the specification?
YES
Go to "COMPONENT INSPECTION".
NO
Repair short to ground in power circuit and go to "VERIFICATION OF VEHICLE REPAIR".
COMPONENT INSPECTION
Refer to DTC B2598.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B2115.
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:22 PM
Page 347
© 2006 Mitchell Repair Information Company, LLC.
2008 HVAC
Blower & A/C Controls (Automatic) - Sedona
CONTROL PANEL
COMPONENT
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:07 PM
Page 1
© 2006 Mitchell Repair Information Company, LLC.
Microsoft
Monday, May 24, 2010 3:56:14 PM
Page 1
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст