Kia Sedona (2008 year). Instruction — part 165
Fig. 99: Measuring Voltage Value Between Terminal 10,11 Of Outside Mirror And Chassis
Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage. Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
NO
Substitute with a known-good ADM and check for proper operation.
If the problem is corrected, replace ADM and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1910.
DTC B1912 RIGHT OSM HORIZONTAL MOTOR OR SENSOR ERROR
COMPONENT LOCATION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 129
© 2006 Mitchell Repair Information Company, LLC.
Fig. 100: Locating ADM, Power Window Motor, Front Door Speaker & Front Door Key Switch
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
Refer to DTC B1954.
DTC DESCRIPTION
The ECM sets DTC B1912 if signal voltage of right outside mirror horizontal sensor is out of range.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Select "Diagnostic Trouble Codes (DTCs)"mode and monitor "DTC Status" parameter.
4. Is the DTC B1912 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION procedure.
Item
Detecting Condition
Possible Cause
DTC Strategy
Check Voltage
short in signal harness
short in power harness
Faulty outside mirror motor
Faulty outside mirror sensor
Faulty ADM
Enable Conditions
IGN `ON' & Engine `OFF'
Threshold value
1.0V < Output voltage < 3.88V
Detecting time
50 ms
FAIL SAFE
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 130
© 2006 Mitchell Repair Information Company, LLC.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical
damage.
2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination,
deterioration, or damage.
3. Has a problem been found?
YES
Repair as necessary and go to "VERIFICATION VEHICLE REPAIR" procedure.
NO
Go to SIGNAL CIRCUIT INSPECTION procedure.
SIGNAL CIRCUIT INSPECTION
1. Check for open in harness
1. Ignition "OFF".
2. Disconnect right outside mirror.
3. Measure resistance between terminal "12" of ADM and chassis ground.
Specification :Approx. infinity ohms
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 131
© 2006 Mitchell Repair Information Company, LLC.
Fig. 101: Measuring Resistance Between Terminal 12 Of ADM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within specifications?
YES
Go to "POWER CIRCUIT INSPECTION" procedure.
NO
Check for short in signal harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
POWER SUPPLY CIRCUIT INSPECTION
1. Motor Power circuit Inspection
1. Ignition "OFF"
2. Disconnect right outside mirror.
3. Measure resistance between terminal "9" of ADM and chassis ground.
4. Measure resistance between terminal "11" of ADM and chassis ground.
Specification :Approx. infinity ohms
Fig. 102: Measuring Resistance Between Terminal 11 Of ADM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
5. Is the measured resistance within specifications?
YES
Go to step 1.
NO
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:18 PM
Page 132
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст