Kia Sedona (2008 year). Instruction — part 210
COMPONENT INSPECTION
1. Check parking lamp
1. Ignition "ON" & engine "OFF".
2. Disconnect parking lamp light bulb.
3. Measure the resistance between both terminals of parking lamp light bulb.
Specification: approx. 0.04 ohms
(If light bulb fails, infinity ohms is measured.)
Fig. 265: Measuring Resistance Between Both Terminals Of Stop Lamp Light Bulb
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within the specification?
YES
Go to step 2.
NO
Replacing the light bulb with `light bulb for test', if normal operating condition is confirmed,
Replace `light bulb for test' with `new light bulb' and go to "VERIFICATION OF VEHICLE
REPAIR".
2. Check FAM
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Check if DTC is erased after replacing FAM with "FAM for test".
4. Is the DTC erased?
YES
Replace "FAM for test" with "new FAM" and go to "VERIFICATION OF VEHICLE
REPAIR".
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 309
© 2006 Mitchell Repair Information Company, LLC.
NO
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage. Repair or replace if necessary and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B2119.
DTC B2573 RIGHT PARKING LAMP CIRCUIT OPEN ERROR
COMPONENT LOCATION
Refer to DTC B2535.
GENERAL DESCRIPTION
FAM is a part of BCM with DDM, ADM, IPM, RAM, IMS and Cluster module. Each part of BCM is
connected to one another through CAN communication line for efficient communication. Those modules
control front/rear, driver/passenger seat, cluster with electrical signal and they share information with other
modules. FAM (Front Area Module) set up at engine room controls various lamps (fog lamp, headlamp. stop
lamp, turn signal lamp), wiper and performs system error checking as well. Received multi function switch turn
signal lamp signal from IPM through CAN line, FAM controls turn signal lamp with integrated IPS. IPS is a
semi-conductor element which performs roles of fuse and relay. In addition to those roles, it performs sensing
circuit error, circuit protection.
DTC DESCRIPTION
The ECM sets DTC B2573 if open in Right parking lamp circuit is detected.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF" & FAM: "ON".
3. Select "Diagnostic Trouble Codes (DTCs)" mode and monitor "DTC Status" parameter.
Item
Detecting Condition
Possible Cause
DTC Strategy
Resistance check
Open in power circuit
Light bulb failure
Enable Conditions
IGN: ON, ENG: OFF
Threshold value
infinity ohms
Detecting time
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 310
© 2006 Mitchell Repair Information Company, LLC.
Fig. 266: Identifying Scan Tool Display - Diagnostic Trouble Codes (DTCs)
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the DTC B2573 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
1. Electrical systems consist of a lot of harness and connectors, poor connection of terminals can cause
various problems and damage of component.
2. Check poor connection, bedding, corrosion, contamination, deformation of connector and it terminals.
3. Is any problem found?
YES
Repair if necessary and go to "VERIFICATION OF VEHICLE REPAIR".
NO
Go to POWER SUPPLY CIRCUIT INSPECTION.
POWER SUPPLY CIRCUIT INSPECTION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 311
© 2006 Mitchell Repair Information Company, LLC.
1. Check open in power circuit
1. Ignition "ON" & engine "OFF".
2. Measure the resistance between parking lamp power circuit of FAM (BCM-FE-1 ) and parking
lamp (E25-2).
Specification: 0 ohms
Fig. 267: Measuring Resistance Between Parking Lamp Power Circuit Of FAM And Parking
Lamp
Courtesy of KIA MOTORS AMERICA, INC.
3. Is the measured resistance within the specification?
YES
Go to "GROUND CIRCUIT INSPECTION".
NO
Repair open in power circuit and go to "VERIFICATION OF VEHICLE REPAIR".
GROUND CIRCUIT INSPECTION
1. Check open in ground circuit
1. Ignition "ON" & engine "OFF".
2. Measure the resistance between parking lamp ground circuit (E25-3) and chassis ground.
Specification: 0 ohms
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 312
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст