Kia Sedona (2008 year). Instruction — part 154
REPAIR" procedure.
NO
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage.
Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE REPAIR"
procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1102.
DTC B1603 CAN BUS OFF FAILURE
COMPONENT LOCATION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 85
© 2006 Mitchell Repair Information Company, LLC.
Fig. 71: Identifying Component Location - CAN Bus Physical Error, Bus Failure
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
Refer to DTC B1602.
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 86
© 2006 Mitchell Repair Information Company, LLC.
DTC DESCRIPTION
To make communication be more accurate, every signal via CAN BUS contains error flame. Each component
counts error and if accumulative error count in one node is above specified value, the ECM sets DTC B1603
and pertinent component is electronically separated.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Select "Diagnostic Trouble Codes (DTC s)" mode and monitor "DTC Status" parameter.
4. Is the DTC B1603 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
Refer to DTC B1102.
COMPONENT INSPECTION
Refer to DTC B1602.
VERIFICATION OF VEHICLE REPAIR
Item
Detecting Condition
Possible Cause
DTC Strategy
-
IPM Faulty
FAM Faulty
RAM Faulty
IMS Faulty
CLU Faulty
DDM Faulty
ADM Faulty
Enable Conditions
-
Threshold value
-
Detecting time
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 87
© 2006 Mitchell Repair Information Company, LLC.
Refer to DTC B1102.
DTC B1605 LOST COMMUNICATION WITH DDM, BUS FAILURE
COMPONENT LOCATION
Fig. 72: Identifying DDM, IPM, Front Door Key Switch & Power Window Motor
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
Refer to DTC B1602.
DTC DESCRIPTION
The ECM sets DTC B1605 if DDM haven't transmitted DATA for 10sec in normal CAN communicating.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
Item
Detecting Condition
Possible Cause
DTC Strategy
-
Faulty IPM
Open/short in DDM power
harness
Faulty DDM
Poor connection of
connected part
Enable Conditions
-
Threshold value
-
Detecting time
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 88
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст