Kia Sedona (2008 year). Instruction — part 133
2008 ACCESSORIES & BODY, CAB
BCM (Body Control Module) - Sedona
BODY NETWORK SYSTEM
DESCRIPTION
All modules are linked a low speed CAN network.
The input information for the modules is coming from both the CAN network and the hardware components
(actuators and sensors).
FAM (Front Area Module)
Headlamp low/high beam control (with DRL)
Park lamp control
Front fog lamp control
Front turn signal lamp control
Windshield wiper control
Windshield deicer
Diagnostics
IPM (In-Panel Module)
RKE (Remote Keyless Control)
VAS (Voice Alarm System)
Ignition key hole illumination
Switch indicators control
Panel light control
Seat belt warning
Auto light/DRL control (Logic)
Windshield/Rear wiper control (Logic)
Turn and Hazard lamp control (Logic)
Central door lock (Logic)
Windshield deicer timer
Rear glass defog timer
Gateway for ISO-9141 (K-Line)
RAM (Rear Area Module)
Tail lamp control
Turn and Hazard lamp control
Back up lamp control
Rear fog lamp control
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:15 PM
Page 1
© 2006 Mitchell Repair Information Company, LLC.
Microsoft
Monday, May 24, 2010 4:19:26 PM
Page 1
© 2006 Mitchell Repair Information Company, LLC.
Stop lamp outage detection
Sliding door power window/Quarter glass control
Room lamp control
Rear wiper control
Rear glass defog
Fuel filler door open solenoid control
ADM (Assist Drive Module)
DDM (Driver Drive Module)
MODULE INTRODUCTION
FAM/IPM/RAM consists of a power board and an electronic board. The power board contains circuit protection
devices and switching devices. The electronic board uses Intelligent Power Switching (IPS) for HS/LS load
control, logic functions and CAN/K-Line communication. The power board and electronic board are connected
with pin blocks for the Front Area Module (FAM) and VCD (Variable Connection Displacement) for the In-
Panel Module (IPM) and the Rear Area Module (RAM).
Fig. 1: Body Network System Module Locations
Courtesy of KIA MOTORS AMERICA, INC.
FUNCTIONS
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:15 PM
Page 2
© 2006 Mitchell Repair Information Company, LLC.
EXTERIOR LIGHTING FUNCTIONS
The exterior lighting function has to provide the lighting and signalling of the vehicle; it monitors different
available lights in front or at the back of the vehicle:
Park and Tail lamps (with Side marker lamps)
License plate lamps
Headlamps Low Beam
Headlamps High Beam
Front and Rear fog lamps (with the Rear fog lamp switch indicator)
Stop lamps
Backup lamps
Turn signal and side repeater lamps
PARK/TAIL LAMPS FUNCTION
1. Necessary conditions to switch ON:
By putting the headlamp switch in position `Park and Tail lamp' or `headlamp Low Beam' or Auto
light activation or DRL activation
2. Necessary conditions to switch OFF:
If they are released by the headlamp switch (Auto light function deactivated) and if DRL function
is deactivated
If the Auto light function is active but the Auto light Sensor signal status is OFF or Battery Saver
function is active.
3. Functional diagram
Fig. 2: Park/Tail Lamps Functional Diagram
Courtesy of KIA MOTORS AMERICA, INC.
HEADLAMPS LOW BEAM FUNCTION
1. Necessary conditions to switch ON:
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:15 PM
Page 3
© 2006 Mitchell Repair Information Company, LLC.
By putting the headlamp switch in position `headlamp Low Beam' or Auto light activation or DRL
activation.
2. Necessary conditions to switch OFF:
If they are released by the headlamp switch (Auto light function deactivated) and if the DRL
function is deactivated
If the Auto light function is active but the Auto light sensor signal status is not `HL ON'.
3. Functional diagram
Fig. 3: Headlamps Low Beam Functional Diagram
Courtesy of KIA MOTORS AMERICA, INC.
HEADLAMPS HIGH BEAM FUNCTION
1. Necessary conditions to switch ON:
By pushing down the High Beam lever switch if
the headlamp switch is in position `headlamp Low Beam' or the headlamps Low Beam have
been turned ON by the Auto light function.
By pulling the High Beam lever switch toward the driver (Flash to pass activation)
By the DRL function activation for Canada.
2. Necessary conditions to switch OFF:
By pulling back the High Beam lever switch (manual reset by the driver) or
If the headlamps Low Beam are turned OFF or If the Auto light function is active but the Auto light
Sensor signal status is not `HL ON') or
By releasing the Flash To Pass activation and
If the DRL function is deactivated for Canada.
3. Functional diagram
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:15 PM
Page 4
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст