Kia Sedona (2008 year). Instruction — part 69
1. Connect the Dummy and the Dummy Adapter on PAB harness connector.
2. Measure resistance between the terminal 7 and 8 of SRSCM harness connector (A).
Specification (resistance): 1.6-4.7 ohms
Fig. 71: Checking PAB Resistance
3. Is the measured resistance within specification?
YES
Replace the Passenger Airbag (PAB) module. Refer to AIR BAG MODULE
(PASSENGER SIDE) .
NO
Check open circuit.
3. CHECK OPEN CIRCUIT
1. Measure resistance between the terminal 3 of PAB harness connector and the terminal 8 of SRSCM
harness connector (A).
2. Measure resistance between the terminal 4 of PAB harness connector and the terminal 7 of SRSCM
harness connector (A).
Specification (resistance): below 1 ohms
(squib) even if you are using the specified tester.
2008 Kia Sedona EX
2008 RESTRAINTS Troubleshooting (Airbag) - Sedona
Microsoft
Monday, May 24, 2010 3:55:02 PM
Page 79
© 2006 Mitchell Repair Information Company, LLC.
Fig. 72: Checking Open Circuit
3. Is the measured resistance within specification?
YES
Check short circuit.
NO
Repair or replace the wiring harness between the PAB and the SRSCM.
4. CHECK SHORT CIRCUIT
1. Measure resistance between the terminal 3 and 4 of PAB harness connector.
Specification (resistance): infinite
Fig. 73: Checking Short Circuit
2. Is the measured resistance within specification?
YES
Go to next step.
NO
Repair or replace the wiring harness between the PAB and the SRSCM.
2008 Kia Sedona EX
2008 RESTRAINTS Troubleshooting (Airbag) - Sedona
Microsoft
Monday, May 24, 2010 3:55:02 PM
Page 80
© 2006 Mitchell Repair Information Company, LLC.
5. CLEAR THE DTC AND CHECK THE VEHICLE AGAIN
Refer to CLEAR THE DTC AND CHECK THE VEHICLE AGAIN.
DTC B1511 SEAT BELT BUCKLE SWITCH [DRIVER] OPEN OR SHORT TO BATTERY; DTC
B1513 SEAT BELT BUCKLE SWITCH [PASSENGER] OPEN OR SHORT TO BATTERY
DTC DESCRIPTION
The Seat Belt Buckle Switch (BS) circuit consists of the SRSCM and two BS. The SRSCM sets above DTC (s)
if it detects open or short to battery line on the BS circuit. This system decides whether the driver or passenger
seat belt is buckled or not.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
SCHEMATIC DIAGRAM
DTC
Condition
Probable cause
B1511
B1513
Open between BS and SRSCM (Current | <
2.98 mA).
Short to battery line between BS and SRSCM
(Current | < 2.98 mA)
Seat Belt Buckle Switch (BS) Malfunction
SRSCM Malfunction
Open or short to battery line circuit
on wiring harness
Seat Belt Buckle Switch (BS)
SRSCM
2008 Kia Sedona EX
2008 RESTRAINTS Troubleshooting (Airbag) - Sedona
Microsoft
Monday, May 24, 2010 3:55:02 PM
Page 81
© 2006 Mitchell Repair Information Company, LLC.
Fig. 74: Seat Belt Buckle Switch - Schematic Diagram
SPECIFICATION
SEAT BELT BUCKLE SWITCH CURRENT SPECIFICATION
TERMINAL & CONNECTOR INSPECTION
Refer to TERMINAL & CONNECTOR INSPECTION.
INSPECTION PROCEDURE
1. PREPARATION
Refer to PREPARATION OF INSPECTION.
2. CHECK OPEN CIRCUIT
1. Disconnect the BS connector.
2. Measure resistance between the terminal 3 of BS harness connector and the terminal 32 (31) of
SRSCM harness connector (B).
specification (Resistance): below 1 ohms
Fig. 75: Checking Open Circuit
3. Is the measured resistance within specification?
YES
Go to next step.
BS Status
Current (mA)
Related DTC
Open or Short to Battery
< 2.98
B1511, B1513
Unbuckled
4-7
Defect
8.9-9.7
B1515, B1516
Buckled
12-18
Short or Short to Ground
> 22.0
B1512, B1514
2008 Kia Sedona EX
2008 RESTRAINTS Troubleshooting (Airbag) - Sedona
Microsoft
Monday, May 24, 2010 3:55:02 PM
Page 82
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст