Kia Carnival (2007 year). Instruction — part 307

Adjustable Pedal(non-ims)

1. Adjust Pedal allows to activate Adjustable Pedal feature for the non-IMS equipped vehicle, IPM needs to control

the power source (by relay coil control) of the adjustable Pedal switch unit.
There is no Adjustable Pedal switch for Non-IMS version.

2. Functional Diagram

Reverse Drive Exterior Side Mirror

This function is implemented by the DDM. This function turns the 2 external reverse mirrors down when gear box in
reverse position.

Quarter Glass Open/close

1. Working Conditions

This Function is available when Ignition key is in RUN position and for 30sec after end of RUN.

a. Quarter glasses can be controlled by switches situated near driver or switches situated near rear passengers

seat (3rd row of seats).

b. When the switch is pressed the motor output is ON until the switch is released or after 5+/- 1sec. The switch

has to be released and pressed again to command the motor output ON again.

c. If power window lock is activated only driver window is enable by driver side switch and no switches are enable

to open quarter glass.

d. There is no interaction with the sliding doors. It is not forbidden to open the quarter glasses when the sliding

door on the same side is open.

e. No switch information (driver or rear passenger ) prevails on the other. If the main switch and the passenger

side switch are pressed in opposite direction at the same time, window stops moving.

2. Functional Diagram

Open Fuel Filler Door

1. Functional Diagram

Sun Roof Relay Coil

This function defines the condition for switching on or off power feed to sun roof relay coil. This function is available in
RUN position and during after run timer ON.

Power Window Timer

This function defines the conditions for allowing use of power windows, quarter glass, and feed to sunroof relay coil.

Sliding Doors Power Windows

1. Working Conditions

This function is available when ignition key is in RUN position and for 30sec after end of RUN. Window operation
will be canceled if the driver or assist door is opened during the 30sec period after the key is turned from RUN to
ACC or OFF position..

2. Functional Diagram

Power Sliding Door & Power Tailgate

1. Description

There are two sliding doors and one tailgate in the vehicle. A switch is fitted at each B-pillar to permit Power
Sliding Door activation.. For the tailgate, there is also one push button switch. These switches are used to send an
signal of 200 ms minimum to the PSD module (or PTG module).

2. Functional Diagram

Easy Access

1. Description

The easy access function permits automatic rearward movement of the driver seat when the key is removed from
the cylinder. Automatic forward movement of the driver seat will take place when the key is inserted into the
cylinder. This function will be enabled on IMS equipped vehicles when the AUTO button is pressed.
Inhibit Switch should be in P-Position for the Easy Access operation.

2. Functional Diagram

Driver Information

Cluster Indicators

1. The instument cluster indicators listed below are controlled by the In-Panel Module (IPM), Front Area Module

(FAM), or Rear Area Module (RAM) as applicable.
These indicators are:

a. Gearbox status

b. Oil pressure

c. Sediment fuel filter

d. Vacuum

e. Brake fluid

f. Washer fluid

g. Seat belt

h. Park brake

i. Charging voltage

j. Turn indicators

k. High beam

l. Front fog

m. Doors open

n. Tailgate open

o. Stop lamp failure front and rear

2. Functional Diagram

Gearbox Status

The status of the gearbox is sent on the CAN network when the CAN network is available.

Oil Pressure Switch Status

The status of the oil pressure switch is sent on the CAN network when the CAN network is available.

Fuel Filter Status

The FAM receives on digital input the status of the fuel filter (Fuel Filter Input) and sends it (Fuel filter switch) on the
CAN network.

Washer Fluid Sensor Status

The FAM receives on digital input the status of the washer fluid sensor and sends it on the CAN network.
If Washer Fluid Low Input is LOW for more than 10 sec, FAM sends the warning message.

Seat Belt Warning Status

The IPM receives on digital input the status of the seat belt switch and sends the seat belt warning on the CAN
network.
If the Ignition switch status is in RUN or START when the Seat Belt Sw Input is FASTENED, the seat belt warning
indicator is blinking for 6 seconds.
When Seat Belt switch Input is NOT FASTENED, the seat belt warning indicator is blinking for 6 seconds.
If the Seat Belt switch Input is FASTENED during the 6 seconds, the seat belt warning indicator is blinking till the end
of the 6 seconds.
In North America:
the seat belt warning indicator is blinking when Ignition switch is on the status RUN or START and Seat Belt Sw Input
is NOT FASTENED.

Parking Brake Indicator

The indicator manages 3 functions: brake fluid sensor, parking brake warning and vacuum switch.
The vacuum function is available for diesel engine only
The FAM receives on digital input the status of the vacuum switch and the ABS EBD warning and sends them on the
CAN network.
The status of the vacuum switch and the ABS EBD warning are sent on the CAN network when the CAN network is
available.
The FAM receives on digital input the status of the brake fluid sensor and sends it on the CAN network.
The status of the brake fluid sensor is sent on the CAN network when the CAN network is available.
The IPM receives on digital input the status of the parking brake switch and by CAN network the status of the vacuum
switch, the status of the ABS EBD warning, the status of the brake fluid sensor and the speed of the vehicle.