Mazda MX-5 (2018 year). Manual — part 26
▼ Replacing a Tire
WARNING
Always use tires that are in good condition:
Driving with worn tires is dangerous.
Reduced braking, steering, and traction
could result in an accident.
Replace all four tires at the same time:
Replacing just one tire is dangerous. It
could cause poor handling and poor
braking resulting in loss of vehicle control.
Mazda strongly recommends that you
replace all four tires at the same time.
If a tire wears evenly, a wear indicator will
appear as a solid band across the tread.
Replace the tire when this happens.
New tread
Tread wear indicator
Worn tread
You should replace the tire before the band
crosses the entire tread.
NOTE
Tires degrade over time, even when they
are not being used on the road. It is
recommended that tires generally be
replaced when they are 6 years or older.
Heat caused by hot climates or frequent
high loading conditions can accelerate the
aging process. The period in which the tire
was manufactured (both week and year) is
indicated by a 4-digit number.
Refer to Tire Labeling on page 8-25.
Maintenance and Care
Owner Maintenance
6-38
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
▼ Replacing a Wheel
WARNING
Always use wheels of the correct size on
your vehicle:
Using a wrong-sized wheel is dangerous.
Braking and handling could be affected,
leading to loss of control and an accident.
CAUTION
A wrong-sized wheel may adversely affect:
Tire fit
Wheel and bearing life
Ground clearance
Snow-chain clearance
Speedometer calibration
Headlight aim
Bumper height
Tire Pressure Monitoring System
NOTE
When replacing a wheel, make sure the
new one is the same as the original
factory wheel in diameter, rim width,
and offset (inset/outset).
For details, contact an Authorized
Mazda Dealer.
Proper tire balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tires can cause
vibration and uneven wear, such as
cupping and flat spots.
Maintenance and Care
Owner Maintenance
6-39
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
Light Bulbs
Overhead light
Side turn signal lights
High-mount brake light
Trunk light
Front side-marker lights
Front turn signal lights
Headlights (Low/High beam)
Parking lights
Daytime running lights
License plate lights
Brake lights
Taillights
Rear side-marker lights
Reverse lights
Rear turn signal lights
Maintenance and Care
Owner Maintenance
6-40
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
CAUTION
When removing the lens or lamp unit using
a flathead screwdriver, make sure that the
flathead screwdriver does not contact the
interior terminal. If the flathead screwdriver
contacts the terminal, a short circuit may
occur.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
▼ Replacing Exterior Light Bulbs
Headlights, Daytime running lights
(LED type), Parking lights, High-mount
brake light, Brake lights, Taillights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Daytime running lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers.
Removal
Installation
3. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.
4. Turn the socket and bulb assembly
counterclockwise and remove it.
Maintenance and Care
Owner Maintenance
6-41
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse
order of the removal procedure.
Front side-marker lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse
order of the removal procedure.
Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Removal
Installation
Maintenance and Care
Owner Maintenance
6-42
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
4. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector rearward.
5. Turn the socket and bulb assembly
counterclockwise and remove it.
6. Disconnect the bulb from the socket.
7. Install the new bulb in the reverse
order of the removal procedure.
Side turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Removal
Installation
4. Remove the unit by pressing the tab on
the unit with your finger and pulling
the unit forward.
Maintenance and Care
Owner Maintenance
6-43
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
5. Detach the electrical connector from
the unit by pulling it to the rear.
6. Install the new side turn signal unit in
the reverse order of the removal
procedure.
Rear turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.
Removal
Installation
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector downward.
4. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the trunk side trim.
Removal
Installation
Maintenance and Care
Owner Maintenance
6-44
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
5. To provide a hole for inserting a finger
to remove the rear combination lamp
unit later in the procedure, pinch the
top and bottom of the grommet shown
in the figure and press it out of the hole
in the direction of the rear combination
lamp unit.
Grommet
Rear combination lamp
unit
Grommet
Body
6. Apply protective tape as shown in the
figure. Otherwise, the rear combination
lamp unit will contact the body and
may scratch or damage it.
Always apply three layers of protective
tape to the area indicated in the figure.
Protective tape
Rear combination
lamp unit
Area specifically in need
of protection
CAUTION
Do not use tape with strong adhesive
strength. Otherwise, the vehicle paint
may peel off.
Always apply three layers of
protective tape to the area indicated
in the figure. Otherwise, the body
may become scratched or damaged
when pulling out the rear
combination lamp unit.
7. Remove the screw and nut.
Maintenance and Care
Owner Maintenance
6-45
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
8. To remove the rear combination lamp
unit, insert your finger from inside the
trunk and into the hole from which the
grommet was removed in Step 5, and
while holding the lamp lens (round
part) of the rear combination lamp with
your hand, press the rear combination
lamp unit until the hook detaches from
the clip.
Rear combination lamp unit
Hook
Grommet installation
hole
9. After the hook is detached, pull out the
rear combination lamp unit in the
direction of the arrow and remove it.
Grommet installation hole
Clip
Hook
Rear combination
lamp unit
CAUTION
Carefully pull out the rear combination
lamp unit when removing it from the
body.
The wiring may become damaged if the
rear combination lamp unit is forcefully
pulled out.
10. Turn the socket and bulb assembly
counterclockwise and remove it.
11. Disconnect the bulb from the socket.
12. Install the new bulb in the reverse
order of the removal procedure.
Rear side-marker lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
Maintenance and Care
Owner Maintenance
6-46
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse
order of the removal procedure.
Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse
order of the removal procedure.
License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the unit by pressing the tab on
the unit with your finger and pulling
the unit downward.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse
order of the removal procedure.
▼ Replacing Interior Light Bulbs
Overhead light
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens, and then remove the lens by
carefully prying on the edge of the lens
with the flathead screwdriver.
Maintenance and Care
Owner Maintenance
6-47
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse
order of the removal procedure.
Trunk light
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens, and then remove the lens by
carefully prying on the edge of the lens
with the flathead screwdriver.
2. Disconnect the connector from the
unit.
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse
order of the removal procedure.
Maintenance and Care
Owner Maintenance
6-48
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls do
not work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
▼ Fuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work, first
inspect the fuses on the vehicle's left side.
1. Make sure the ignition is switched off,
and other switches are off.
2. Open the fuse panel cover.
3. Pull the fuse straight out with the fuse
puller provided on the fuse block
located in the engine compartment.
4. Inspect the fuse and replace it if it is
blown.
Normal
Blown
5. Insert a new fuse of the same
amperage rating, and make sure it fits
tightly. If it does not fit tightly, have an
expert install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage the
electric system.
6. Reinstall the cover and make sure that
it is securely installed.
Maintenance and Care
Owner Maintenance
6-49
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
NOTE
If the lock is forcefully opened, the fuse
block cover may come in contact with
the frame when it is removed and
become scratched.
When removing the cover, remove it
slowly according to the following
procedure.
1. Disengage the rear lock by
pressing down on the front tab with
your fingers.
2. Remove the front tab while slightly
lifting the front of the cover.
3. Remove the cover while lifting it
and sliding it to the rear.
3. If any fuse but the MAIN fuse is
blown, replace it with a new one of the
same amperage rating.
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is a
high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
4. Reinstall the cover and make sure that
it is securely installed.
Maintenance and Care
Owner Maintenance
6-50
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
▼ Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION
FUSE
RATING
PROTECTED COMPONENT
1
ENG IG3
5 A
―
2
ENG IG2
5 A
―
3
HORN2
7.5 A
Horn
4
C/U IG1
15 A
For protection of various circuits
5
ENG IG1
7.5 A
Engine control system
6
―
―
―
7
INTERIOR
15 A
Overhead light
8
ENG B
7.5 A
Engine control system
9
AUDIO2
15 A
Audio system
10
METER1
10 A
Instrument cluster
11
SRS1
7.5 A
Air bag
12
―
―
―
13
RADIO
7.5 A
Audio system
14
ENGINE3
20 A
Engine control system
15
ENGINE1
10 A
Engine control system
16
ENGINE2
15 A
Engine control system
Maintenance and Care
Owner Maintenance
6-51
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
DESCRIPTION
FUSE
RATING
PROTECTED COMPONENT
17
AUDIO1
25 A
Audio system
18
A/C MAG
7.5 A
Air conditioner
19
AT PUMP
H/L HI
20 A
―
20
AT
15 A
Transmission control system
*
21
D LOCK
25 A
Power door locks
22
H/L RH
20 A
Headlight (RH)
23
ENG B2
7.5 A
Engine control system
24
TAIL
20 A
Taillights, License plate lights, Parking lights
25
DRL
15 A
―
26
ROOM
25 A
Overhead light
27
FOG
15 A
―
28
H/CLEAN
20 A
―
29
STOP
10 A
Brake lights
30
HORN
15 A
Horn
31
H/L LH
20 A
Headlight (LH)
32
ABS/DSC S
30 A
ABS, Dynamic stability control system
33
HAZARD
15 A
Hazard warning flashers, Turn signal lights
34
FUEL PUMP
15 A
Fuel system
35
ENG B3
5 A
―
36
WIPER
20 A
Windshield wipers
37
CABIN B
50 A
For protection of various circuits
38
―
―
―
39
―
―
―
40
ABS/DSC M
50 A
ABS, Dynamic stability control system
41
EVVT
A/R PUMP
20 A
Engine control system
42
EVPS
30 A
Brake control system
43
FAN1
30 A
Cooling fan
44
FAN2
40 A
―
45
ENG.MAIN
40 A
Engine control system
46
EPS
60 A
Power steering system
47
DEFOG
30 A
Rear window defogger
48
IG2
30 A
For protection of various circuits
49
INJECTOR
30 A
Engine control system
50
HEATER
40 A
Air conditioner
Maintenance and Care
Owner Maintenance
6-52
*Some models.
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
DESCRIPTION
FUSE
RATING
PROTECTED COMPONENT
51
―
―
―
52
―
―
―
Fuse block (Left side)
DESCRIPTION
FUSE
RATING
PROTECTED COMPONENT
1
RHT R
30 A
Retractable hardtop (RH)
*
2
RHT L
30 A
Retractable hardtop (LH)
*
3
―
―
―
4
―
―
―
5
F.OUTLET
15 A
Accessory sockets
6
―
―
―
7
AT IND
7.5 A
AT shift indicator
*
8
MIRROR
7.5 A
Power control mirror
9
R_DECK R
30 A
Retractable hardtop (RH)
*
10
R_DECK L
30 A
Retractable hardtop (LH)
*
11
F.WASHER
15 A
Windshield washer
12
P.WINDOW
30 A
Power windows
13
―
―
―
14
SRS2/ESCL
15 A
―
15
SEAT WARM
20 A
Seat warmer
*
16
M.DEF
7.5 A
Mirror defogger
*
Maintenance and Care
Owner Maintenance
*Some models.
6-53
MX-5_8GF7-EA-17J_Edition2
2017-10-31 14:07:27
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст