Mazda CX-3 (2019 year). Manual — part 29
After rotation, inflate all tire pressures to
specification (page 9-7) and inspect the
lug nuts for tightness.
CAUTION
Rotate unidirectional tires and radial tires
that have an asymmetrical tread pattern or
studs only from front to rear, not from side
to side. Tire performance will be reduced if
rotated from side to side.
▼ Replacing a Tire
WARNING
Always use tires that are in good condition:
Driving with worn tires is dangerous.
Reduced braking, steering, and traction
could result in an accident.
Replace all four tires at the same time:
Replacing just one tire is dangerous. It
could cause poor handling and poor
braking resulting in loss of vehicle control.
Mazda strongly recommends that you
replace all four tires at the same time.
If a tire wears evenly, a wear indicator will
appear as a solid band across the tread.
Replace the tire when this happens.
New tread
Tread wear indicator
Worn tread
You should replace the tire before the band
crosses the entire tread.
NOTE
Tires degrade over time, even when they
are not being used on the road. It is
recommended that tires generally be
replaced when they are 6 years or older.
Heat caused by hot climates or frequent
high loading conditions can accelerate the
aging process. You should replace the
spare tire when you replace the other road
tires due to the aging of the spare tire. The
period in which the tire was manufactured
(both week and year) is indicated by a
4-digit number.
Refer to Tire Labeling on page 8-25.
Maintenance and Care
Owner Maintenance
6-38
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
▼ Temporary Spare Tire
Inspect the temporary spare tire at least
monthly to make sure it is properly
inflated and stored.
NOTE
The temporary spare tire condition
gradually deteriorates even if it has not
been used.
The temporary spare tire is easier to
handle because of its construction which is
lighter and smaller than a conventional
tire. This tire should be used only for an
emergency and only for a short distance.
Use the temporary spare tire only until the
conventional tire is repaired, which should
be as soon as possible.
Refer to Tires on page 9-7.
CAUTION
Do not use your temporary spare tire rim
with a snow tire or a conventional tire.
Neither will properly fit and could
damage both tire and rim.
The temporary spare tire has a tread life
of less than 5,000 km (3,000 miles). The
tread life may be shorter depending on
driving conditions.
The temporary spare tire is for limited
use, however, if the tread wear
solid-band indicator appears, replace the
tire with the same type of temporary
spare (page 6-38).
NOTE
Tires degrade over time, even when they
are not being used on the road. It is
recommended that tires generally be
replaced when they are 6 years or older.
Heat caused by hot climates or frequent
high loading conditions can accelerate the
aging process. You should replace the
spare tire when you replace the other road
tires due to the aging of the spare tire. The
period in which the tire was manufactured
(both week and year) is indicated by a
4-digit number.
Refer to Tire Labeling on page 8-25.
Maintenance and Care
Owner Maintenance
6-39
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
▼ Replacing a Wheel
WARNING
Always use wheels of the correct size on
your vehicle:
Using a wrong-sized wheel is dangerous.
Braking and handling could be affected,
leading to loss of control and an accident.
CAUTION
A wrong-sized wheel may adversely affect:
Tire fit
Wheel and bearing life
Ground clearance
Snow-chain clearance
Speedometer calibration
Headlight aim
Bumper height
Tire Pressure Monitoring System
*
NOTE
•
When replacing a wheel, make sure the
new one is the same as the original
factory wheel in diameter, rim width,
and offset (inset/outset).
•
For details, contact an Authorized
Mazda Dealer.
Proper tire balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tires can cause
vibration and uneven wear, such as
cupping and flat spots.
Maintenance and Care
Owner Maintenance
6-40
*Some models.
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
Light Bulbs
With LED Headlights
With Halogen Headlights
Overhead lights (Front) /Map lights
Overhead lights (Rear)
Overhead lights (Front) /Map lights
Headlights (High
beam)/Daytime running
lights
Headlights (Low beam)
Parking lights/Daytime
running lights
Side turn signal lights
Fog lights
Parking lights/Front
side-marker lights
Front side-marker lights
Front turn signal lights
Luggage compartment light
License plate lights
Reverse lights
Taillights
Rear turn signal lights
Rear side-marker lights
Brake lights/Taillights
High-mount brake light
Some models.
Side turn signal lights
Headlights (High beam)
Headlights (Low beam)
Fog lights
Front turn signal lights
Maintenance and Care
Owner Maintenance
6-41
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
WARNING
Never touch the glass portion of a halogen
bulb with your bare hands and always
wear eye protection when handling or
working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it will
explode and serious injuries could be
caused by the flying glass.
If the glass portion is touched with bare
hands, body oil could cause the bulb to
overheat and explode when lit.
Always keep halogen bulbs out of the reach
of children:
Playing with a halogen bulb is dangerous.
Serious injuries could be caused by
dropping a halogen bulb or breaking it
some other way.
CAUTION
When removing the lens or lamp unit using
a flathead screwdriver, make sure that the
flathead screwdriver does not contact the
interior terminal. If the flathead screwdriver
contacts the terminal, a short circuit may
occur.
NOTE
•
To replace the bulb, contact an
Authorized Mazda Dealer.
•
If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
•
Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
▼ Replacing Exterior Light Bulbs
Headlights (With LED headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Headlights/Daytime running lights
(With halogen headlights)
High-beams bulbs/Daytime running
lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector downward.
Maintenance and Care
Owner Maintenance
6-42
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
4. Turn the socket and bulb assembly to
remove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
5. Install the new bulb in the reverse
order of the removal procedure.
Low-beam bulbs
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector downward.
4. Turn the socket and bulb assembly to
remove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
5. Install the new bulb in the reverse
order of the removal procedure.
Parking lights/Daytime running lights/
Front side-marker lights (With LED
headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Maintenance and Care
Owner Maintenance
6-43
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
Parking lights/Front side-marker lights
(With halogen headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse
order of the removal procedure.
Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse
order of the removal procedure.
Fog lights
*
, Side turn signal lights
*
,
Brake lights/Taillights (LED type), Rear
side-marker lights (LED type),Taillights
(LED type)
*
, High-mount brake light,
Reverse lights (LED type)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized
Mazda Dealer when the replacement is
necessary.
Maintenance and Care
Owner Maintenance
6-44
*Some models.
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
Rear turn signal lights, Brake lights/
Taillights (Bulb type), Rear side-marker
lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the bolts counterclockwise and
remove them.
3. Pull the unit rearward to remove it.
4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Disconnect the bulb from the socket.
Rear turn signal lights
Brake lights/Taillights
Rear side-marker lights
6. Install the new bulb in the reverse
order of the removal procedure.
Maintenance and Care
Owner Maintenance
6-45
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
Reverse lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse
order of the removal procedure.
License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse
order of the removal procedure.
▼ Replacing Interior Light Bulbs
Overhead lights (Front)/Map lights,
Overhead lights (Rear)
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens, and then remove the lens by
carefully prying on the edge of the lens
with the flathead screwdriver.
2. Disconnect the bulb by pulling it out.
Maintenance and Care
Owner Maintenance
6-46
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
Overhead lights (Front)/Map lights
Overhead lights (Rear)
Edge
3. Install the new bulb in the reverse
order of the removal procedure.
Luggage compartment light
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens unit by
carefully prying on the edge of the lens
unit with the flathead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse
order of the removal procedure.
Maintenance and Care
Owner Maintenance
6-47
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls do
not work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
▼ Fuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work, first
inspect the fuses on the vehicle's left side.
1. Make sure the ignition is switched off,
and other switches are off.
2. Open the fuse panel cover.
3. Pull the fuse straight out with the fuse
puller provided on the fuse block
located in the engine compartment.
4. Inspect the fuse and replace it if it is
blown.
Normal
Blown
5. Insert a new fuse of the same
amperage rating, and make sure it fits
tightly. If it does not fit tightly, have an
expert install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage the
electric system.
6. Reinstall the cover and make sure that
it is securely installed.
Maintenance and Care
Owner Maintenance
6-48
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is
blown, replace it with a new one of the
same amperage rating.
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is a
high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
4. Reinstall the cover and make sure that
it is securely installed.
Maintenance and Care
Owner Maintenance
6-49
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
▼ Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION
FUSE
RATING
PROTECTED COMPONENT
1
C/U IG1
15 A
For protection of various circuits
2
ENGINE IG1
7.5 A
Engine control system
3
SUNROOF
10 A
Moonroof
*
4
INTERIOR
15 A
Overhead light, Audio system
5
7.5 A
Engine control system
6
AUDIO2
ENGINE4
15 A
Engine control system
7
METER1
10 A
Instrument cluster
8
SRS1
7.5 A
Air bag
9
METER2
7.5 A
―
10
RADIO
7.5 A
Audio system
11
ENGINE3
15 A
Engine control system
12
ENGINE1
15 A
―
13
ENGINE2
15 A
Engine control system
14
AUDIO1
25 A
Audio system
Maintenance and Care
Owner Maintenance
6-50
*Some models.
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
DESCRIPTION
FUSE
RATING
PROTECTED COMPONENT
15
A/C MAG
7.5 A
Air conditioner
16
AT PUMP
15 A
―
17
AT
15 A
Transaxle control system
18
D.LOCK
25 A
Power door locks
19
H/L RH
20 A
Headlight (RH)
20
7.5 A
Engine control system
21
TAIL
20 A
Taillights, License plate lights, Parking lights
22
ST.HEATER
15 A / 20 A Heated steering wheel
*
, Headlight
*
23
ROOM
25 A
Overhead light
24
FOG
15 A
Fog lights
*
25
H/CLEAN
20 A
―
26
STOP
10 A
Brake lights
27
HORN
15 A
Horn
28
H/L LH
20 A
Headlight (LH)
29
ABS/DSC S
30 A
ABS, Dynamic stability control system
30
HAZARD
15 A
Hazard warning flashers, Turn signal lights
31
FUEL PUMP
SCR
15 A
Fuel system
32
FUEL WARM
25 A
―
33
WIPER
20 A
Front window wiper
34
50 A
For protection of various circuits
35
FAN2
EPB L
30 A
Electric parking brake (LH)
36
FUEL PUMP
30 A
―
37
ABS/DSC M
50 A
ABS, Dynamic stability control system
38
EVVT
20 A
Engine control system
39
―
―
―
40
FAN1
EPB R
30 A
Electric parking brake (RH)
41
FAN3
40 A
Cooling fan
42
ENG.MAIN
40 A
Engine control system
43
EPS
60 A
―
44
DEFOG
40 A
Rear window defogger
45
IG2
30 A
For protection of various circuits
46
INJECTOR
ENG.SUB
30 A
Engine control system
Maintenance and Care
Owner Maintenance
*Some models.
6-51
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
DESCRIPTION
FUSE
RATING
PROTECTED COMPONENT
47
HEATER
40 A
Air conditioner
48
P.WINDOW1
30 A
Power windows
49
DCDC DE
40 A
―
Fuse block (Left side)
DESCRIPTION
FUSE
RATING
PROTECTED COMPONENT
1
―
―
―
2
―
―
―
3
AUDIO2
15 A
Audio system
4
ST.HEATER
10 A
Heated steering system
*
5
F.OUTLET
15 A
Accessory sockets
6
―
―
―
7
AT IND
7.5 A
AT shift indicator
*
8
MIRROR
7.5 A
Power control mirror
9
―
―
―
10
P.WINDOW2
25 A
Power windows
11
R.WIPER
15 A
Rear window wiper and washer
12
P.SEAT D
30 A
Power seat
*
13
―
―
―
14
SRS2/ESCL
15 A
―
15
SEAT WARM
20 A
Seat warmer
*
Maintenance and Care
Owner Maintenance
6-52
*Some models.
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
DESCRIPTION
FUSE
RATING
PROTECTED COMPONENT
16
M.DEF
7.5 A
Mirror defogger
*
Maintenance and Care
Owner Maintenance
*Some models.
6-53
CX-3_8GR7-EA-18B_Edition1
2017-12-20 16:18:14
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст