Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 629
DRIVE LINE CONTROL SYSTEM (TOD)
4B2–36
Step
Action
Yes
No
1
1. Connect TECH 2.
While running in TOD mode, does TECH–2’s front speed sensor
indication change with vehicle speed?
Go to Step 2
Repair and
inspection front
speed sensor
tone wheel.
Go to Step 6
2
1. Clear the trouble code.
While running at 40 km/h or 25 mph in TOD mode for 30
consecutive sec, is the trouble code reissued?
Go to Step 3
The trouble is not
reproduced.
Refer to
“Troubles
intermittently
observed”.
3
1. Turn off the starter switch.
2. Disconnect the ECU connector (B–48) and (B–49).
Is there the continuity between the connector (B–48) terminal 10
and 25?
Repair the circuit.
Go to Step 6
Go to Step 4
4
1. Disconnect the transfer connector (M–27).
Is there the continuity between the connector (B–48) terminal 10
and the connector (M–27) terminal 6, the connector (B–49)
terminal 12 and connector (M–27) terminal 2, and the connector
(B–49) terminal 13 and connector (M–27) terminal 10?
Replace the front
speed sensor.
Go to Step 5
Repair the circuit.
Go to Step 5
5
1. Clear the trouble code.
While running at 40 km/h or 25 mph in TOD mode for 30
consecutive sec, is the trouble code reissued?
Replace ECU.
Go to Step 6
Go to Step 6
6
1. Check that all the parts are mounted.
2. Clear the trouble code.
Is this step complete?
Repeat the
“Diagnosis Flow”.
Return to Step 6
4B2–37
DRIVE LINE CONTROL SYSTEM (TOD)
Check flow
Trouble code
Phenomenon
Standard
4
27
(P1738)
The front speed sensor no pulse.
Hi level : 4.5
∼
6.0 V
Lo level : 0.7
∼
2.0 V
Frequency (F) =
700 – 850 Hz (at 30 mile/h)
NOTE: Find the trouble in which the pulse corresponding
to the running speed is not input.
D04RY00004
DRIVE LINE CONTROL SYSTEM (TOD)
4B2–38
Step
Action
Yes
No
1
1. Connect TECH 2.
While running in TOD mode, does TECH–2’s rear speed sensor
indication change with vehicle speed?
Go to Step 2
Repair and
inspection front
speed sensor
tone wheel.
Go to Step 6
2
1. Clear the trouble code.
While running at 40 km/h or 25 mph in TOD mode for 30
consecutive sec, is the trouble code reissued?
Go to Step 3
The trouble is not
reproduced.
Refer to
“Troubles
intermittently
observed”.
3
1. Turn off the starter switch.
2. Disconnect the ECU connector (B–48) and (B–49).
Is there the continuity between the connector (B–48) terminal 23
and 25?
Repair the circuit.
Go to Step 5
Go to Step 4
4
1. Disconnect the transfer connector (M–27).
Is there the continuity between the connector (B–48) terminal 23
and the connector (M–27) terminal 5, the connector (B–49)
terminal 12 and connector (M–27) terminal 1, and the connector
(B–49) terminal 13 and connector (M–27) terminal 9?
Replace the rear
speed sensor.
Go to Step 5
Repair the circuit.
Go to Step 5
5
1. Clear the trouble code.
While running at 40 km/h or 25 mph in TOD mode for 30
consecutive sec, is the trouble code reissued?
Replace ECU.
Go to Step 6
Go to Step 6
6
1. Check that all the parts are mounted.
2. Clear the trouble code.
Is this step complete?
Repeat the
“Diagnosis Flow”.
Return to Step 6
4B2–39
DRIVE LINE CONTROL SYSTEM (TOD)
Check flow
Trouble code
Phenomenon
Standard
5
24
(P1733)
Rear speed sensor signal open or
GND short, speed sensor COM
open.
0.3 V > sensor voltage
NOTE: The following procedure shows the case that the
front or rear sensor common grounding line is broken.
D04RY00004
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст