Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 580
POWER ASSISTED SYSTEM
2A–49
Installation
1. Install steering wheel by aligning the setting marks
made when removing.
CAUTION: Never apply force to the steering wheel
in direction of the shaft by using a hammer or other
impact tools in an attempt to remove the steering
wheel. The steering shaft is designed as an energy
absorbing unit.
2. Tighten the steering wheel fixing nut to the specified
torque.
Torque: 34 N·m (25 lb ft)
3. Connect horn lead.
4. Support the module and carefully connect the module
connector.
CAUTION:
D
Never use the air bag assembly from another
vehicle. Use only the air bag assembly for “UX”.
D
The driver’s air bag assembly (Inflator module)
for 1999 model has different characteristic to the
parts for 1998 model.When replace the driver’s
air bag assembly, confirm the parts number and
use only the parts for 1999 model. (The driver’s
air bag assembly for 1999 model has “yellow” bar
codes label. 1998 model has “white” bar codes
label.)
NOTE: Pass the lead wire through the tabs on the plastic
cover (wire protector) of inflator to prevent lead wire from
being pinches.
D
Secure the module with one bolt to relieve weight on
the wire connector.
D
Tighten bolts to specified sequence as illustrated.
Torque: 8 N·m (69 lb in)
827RW003
5. Connect the yellow 2-way SRS connector located
under the steering column.
6. Connect the battery “–” terminal cable.
7. Turn the ignition switch to “ON” while watching
warning light. Light should flash 7 times and then go
off. If lamp does not operate correctly, refer to
Restraints section.
2A-50
POWER ASSISTED SYSTEM
Combination Switch
Combination Switch and Associated Parts
431RW001
Legend
(1) Steering Column Cover
(2) Steering Wheel
(3) Inflator Module
(4) Combination Switch and SRS Coil Assembly
(5) Front Console Assembly
(6) Steering Lower Cover
(7) Lower Cluster Assembly
Removal
1. Turn the steering wheel so that the vehicle’s wheels
are pointing straight ahead.
2. Turn the ignition switch to “LOCK”.
3. Disconnect the battery “–” terminal cable, and wait at
least 5 minutes.
4. Disconnect the yellow 2-way SRS connector located
under the steering column.
CAUTION: The wheels of the vehicle must be
straight ahead and the steering column in the
“LOCK” position before disconnecting the steering
wheel. Failure to do so will cause the coil assembly
to become uncentered which will cause damage to
the coil assembly.
5. Remove the transmission (for M/T) and transfer
control lever knob. Disconnect the wiring harness
connectors then remove front console assembly.
6. Remove lower cluster assembly.
7. Remove the engine hood opening lever, then remove
steering lower cover.
POWER ASSISTED SYSTEM
2A–51
8. Loosen the inflator module fixing bolt from behind the
steering wheel assembly using a TORX
driver or
equivalent until the inflator module can be released
from steering assembly. Disconnect the yellow 2-way
SRS connector located behind the inflator module,
then remove inflator module.
827RT008
827RW002
WARNING: THE INFLATOR MODULE SHOULD
ALWAYS BE CARRIED WITH THE URETHANE
COVER AWAY FROM YOUR BODY AND SHOULD
ALWAYS BE LAID ON A FLAT SURFACE WITH THE
URETHANE SIDE UP. THIS IS NECESSARY
BECAUSE A FREE SPACE IS PROVIDED TO ALLOW
THE AIR CUSHION TO EXPAND IN THE UNLIKELY
EVENT OF ACCIDENTAL DEPLOYMENT.
OTHERWISE, PERSONAL INJURY MAY RESULT.
827RS016
9. Apply a setting mark (1) across the steering wheel
and shaft so parts can be reassembled in their original
position. Move the front wheels to the straight ahead
posision, then use steering wheel remover J–29752
to remove the steering wheel.
430RW001
CAUTION: Never apply force to the steering wheel
in direction of the shaft by using a hammer or other
impact tools in an attempt to remove the steering
wheel. The steering shaft is designed as an energy
absorbing unit.
2A-52
POWER ASSISTED SYSTEM
430RT009
10. Remove steering column cover.
11. Disconnect the wiring harness connectors located
under the steering column, then remove combination
switch and SRS coil assembly.
NOTE: The SRS coil is a part of the combination switch
assembly, which can not be replaced separately.
Therefore, be sure not to remove the SRS coil from the
combination switch assembly.
825RW030
Installation
1. Install combination switch and SRS coil assembly.
After installation of combination switch assembly,
connect the combination switch wiring harness
connector and the SRS 2-way connector located
under the steering column. Then turn the SRS coil
counterclockwise to full, return about 3 turns and align
the neutral mark.
CAUTION: When turning the SRS coil
counterclockwise to full, stop turning if resistance is
felt. Forced further turning may damage to the cable
in the SRS coil.
826RW014
2. When installing the steering column cover, be sure to
route each wire harness as illustrated so that the
harnesses do not catch on any moving parts.
825RW017
Legend
(1) Steering Column Cover
(2) Starter Switch Harness
(3) Combination Switch Harness
(4) Inflator Module Harness
3. Align the setting marks made when removing then
install steering wheel.
CAUTION: Never apply force to the steering wheel
in direction of the shaft by using a hammer or other
impact tools in an attempt to remove the steering
wheel. The steering shaft is designed as an energy
absorbing unit.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст