Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 774
6E–120
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Manifold Absolute Pressure (MAP) Output Check
Step
Action
Value(s)
Yes
No
1
1. Turn the ignition “OFF” and leave it “OFF” for 15
seconds.
2. Ignition “ON”. Don’t crank engine.
3. The Tech 2 should indicate a manifold absolute
pressure (MAP) sensor voltage.
4. Compare this scan reading to scan reading of a
known good vehicle obtained using the exact same
procedure as in Steps 1-4.
Is the voltage reading the same +/–0.40 volt?
—
Go to
Step 2
Go to
Step 5
2
1. Disconnect the vacuum hose at the MAP sensor
and plug the hose.
2. Connect a hand vacuum pump to the MAP sensor.
3. Start the engine.
4. Apply 34 kPa (10 in.Hg) of vacuum and note the
voltage change.
Is the voltage change 1.5-2.1 volts less than Step 1?
—
Go to
Step 3
Go to
Step 4
3
Check the sensor cover for leakage or restriction.
Does the hose supply vacuum to the MAP sensor only?
—
Go to
Step 5
Go to
Step 4
4
Repair the hose blockage.
Is the action complete?
—
Verify repair
—
5
Check the sensor connection.
Is the sensor connection good?
—
Go to
Step 6
Go to
Step 7
6
Refer to
On-Vehicle Service, MAP Sensor.
Is the action complete?
—
Verify repair
—
7
Repair the poor connection.
Is the action complete?
—
Verify repair
—
6E–121
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Evaporative (EVAP) Emissions Canister Purge Valve Check
D06R200084
Circuit Description
Canister purge is controlled by a solenoid valve that
allows manifold vacuum to purge the canister. The
powertrain control module (PCM) supplies a ground to
energize the solenoid valve (purge “ON”). The EVAP
purge solenoid control is turned “ON” and “OFF” several
times a second. The duty cycle (pulse width or “ON” time)
is determined by engine operating conditions including
load, throttle position, coolant temperature and ambient
temperature. The duty cycle is calculated by the PCM
and the purge solenoid is enabled when the appropriate
conditions have been met:
D
The engine run time after start is more than 60
seconds.
D
The engine coolant temperature is above 30
°
C
(86
°
F).
D
The fuel control system is operating in the closed-loop
mode.
Diagnostic Aids
D
Make a visual check of vacuum hoses.
D
Check the throttle body for cracks.
D
Check the malfunction indicator lamp for a possible
mechanical problem.
Test Description
The number(s) below refer to the step number(s) on the
Diagnostic Chart.
1. Check to see if the solenoid is open or closed. The
solenoid is normally de-energized in this step, so it
should be closed.
2. This step checks to determine if the solenoid was
open due to an electrical circuit problem or a
defective solenoid.
3. This should normally energize the solenoid, opening
the valve and allowing the vacuum to drop (purge
“ON”).
6E–122
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Evaporative (EVAP) Emissions Canister Purge Valve Check
Step
Action
Value(s)
Yes
No
1
1. Ignition “OFF”.
2. Ignition “ON”, engine “OFF”.
3. At the throttle body, disconnect the hose that goes
to the purge solenoid.
4. Using a hand vacuum pump with an attached
vacuum gauge J 23738-A, apply vacuum (10 in. Hg
or 34 kPa) to the solenoid.
Does the solenoid hold the vacuum?
—
Go to
Step 3
Go to
Step 2
2
1. Disconnect the solenoid electrical connector.
2. As in Step 1, apply vacuum (10 in. Hg or 34 kPa) to
the solenoid.
Does the solenoid hold the vacuum?
—
Go to
Step 4
Go to
Step 7
3
1. At the throttle body, put a cap over the vacuum port
where the hose was disconnected for testing. This
is to prevent a vacuum leak when the engine is
started.
2. Ignition “OFF”.
3. Install the Tech 2.
4. Apply vacuum to the purge solenoid with the hand
vacuum pump.
5. Start the engine, run at 2500 RPM.
6. Using the Tech 2, select Powertrain, 3.5–V6 6VE1,
F3: Misc. Tests, F2: EVAP Purge, F0: EVAP Purge.
(Refer to the Misellaneous Test.)
7. Turn the purge solenoid “ON”.
Did the vacuum drop when the purge was turned on?
—
Go to
Step 8
Go to
Step 9
4
Check for a short to ground in the S7 Pin wire.
Is there a short?
—
Go to
Step 5
Go to
Step 6
5
Repair the short to ground.
Is the action complete?
—
Verify repair
—
6
Replace the PCM.
IMPORTANT: The replacement PCM must be
programmed. Refer to
On-Vehicle Servicein
Powertrain Control Module and Sensors for
procedures.
And also refer to latest Service Bulletin.
Check to see if the Latest software is released or not.
And then Down Load the LATEST PROGRAMMED
SOFTWARE to the replacement PCM.
Is the action complete?
—
Verify repair
—
7
Replace the faulty purge solenoid. Refer to
On-Vehicle
Service, EVAP Canister Purge Solenoid.
Is the action complete?
—
Verify repair
—
6E–123
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Evaporative (EVAP) Emissions Canister Purge Valve Check
(Cont'd)
Step
No
Yes
Value(s)
Action
8
1. Turn the ignition “OFF”.
2. At the throttle body, install a vacuum gauge where
the hose from the purge solenoid was disconnected
for testing.
3. Start the engine.
4. Stabilize the engine speed at about 2500 RPM.
5. Momentarily snap the throttle open and let it return
to idle.
Is there approximately 10 in. Hg (34 kPa) of vacuum
available at the EVAP emission canister purge
solenoid?
—
No problem
found in the
EVAP
emission
canister
purge valve
check
Check the
Procedure
Refer to
Diagnostic
Aids
9
1. Disconnect the solenoid electrical connector.
2. Connect a test lamp between the harness
terminals.
Does the test lamp light?
—
Go to
Step 7
Go to
Step 10
10
Probe terminal A and terminal B with a test lamp to
ground.
Does the test lamp light on both terminals?
—
Go to
Step 11
Go to
Step 12
11
Repair the short to voltage in the S7 Pin wire.
Is the action complete?
—
Verify repair
—
12
Does one of the terminals light the test lamp?
—
Go to
Step 13
Go to
Step 14
13
Check for an open in the S7 Pin wire between the purge
solenoid and the PCM.
Was there an open circuit?
—
Go to
Step 15
Go to
Step 6
14
Repair the open in the BLK/YEL wire.
Is the action complete?
—
Verify repair
—
15
Repair the open in the S7 Pin wire.
Is the action complete?
—
Verify repair
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст