Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1263
6E1–128
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
be useful in determining vehicle mileage since the
Diagnostic Trouble Code was last set.
Test Description
Number(s) below refer to the step number(s) on the
Diagnostic Chart:
2. Verifies that the fault is present.
3. If Diagnostic Trouble Code P0112 can be repeated
only by duplicating the Failure Records condition,
refer to the Temperature vs. Resistance Value table.
The table may be used to test the IAT sensor at
various temperatures to evaluate the possibility of a
”shifted” sensor that may be stored above or below a
certain temperature. If this is the case, replace the
IAT sensor. If the IAT sensor appears to be OK, the
fault is intermittent; refer to Diagnostic Aids.
Intake Air Temperature Sensor
°
C
°
F
OHMS
Temperature vs. Resistance Values (approximate)
100
212
177
80
176
332
60
140
667
45
113
1188
35
95
1802
25
77
2796
15
59
4450
5
41
7280
–5
23
12300
–15
5
21450
–30
–22
52700
–40
–40
100700
6E1–129
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
DTC P0112 Intake Air Temperature (IAT) Sensor Circuit Low Input
Step
Action
Value(s)
Yes
No
1
Was the ”On–Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to OBD
System
Check
2
1. Ignition ON, engine OFF.
2. Using a Tech 2, monitor the intake air temperature
(IAT).
Is the intake air temperature greater than the specified
value?
148
°
C
(283
°
F)
Go to Step 4
Go to Step 3
3
1. Ignition ON, engine OFF. Review and record Tech 2
Failure Records data.
2. Operate the vehicle within Failure Records
conditions as noted.
3. Using a Tech 2, monitor the ”DTC” info for
Diagnostic Trouble Code P0112.
Does the Tech 2 indicate DTC P0112 failed this
ignition?
—
Refer to Test
Description
Refer to
Diagnostic
Aids
4
1. Ignition OFF.
2. Disconnect the IAT sensor electrical connector.
3. Ignition ON.
4. Observe the intake air temperature on the Tech 2.
Is the intake air temperature below the specified value?
–38
°
C
(–36
°
F)
Go to Step 6
Go to Step 5
5
1. Ignition OFF.
2. Disconnect the PCM electrical connectors.
3. Check the IAT sensor signal circuit for a short to
ground.
Is the IAT sensor signal circuit shorted to ground?
—
Verify Repair
Go to Step 7
6
Replace the IAT sensor.
Is the action complete?
—
Verify Repair
—
7
Replace the PCM.
IMPORTANT: The replacement PCM must be
programmed. Refer to On–Vehicle Service in
Powertrain Control Module and Sensors for
procedures.
And also refer to latest Service Bulletin.
Check to see if the Latest software is released or not.
And then Down Load the LATEST PROGRAMMED
SOFTWARE to the replacement PCM.
Is the action complete?
—
Verify Repair
—
6E1–130
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
DIAGNOSTIC TROUBLE CODE (DTC)
P0113 INTAKE AIR TEMPERATURE (IAT) SENSOR CIRCUIT HIGH INPUT
060R100027
Circuit Description
The intake air temperature (IAT) sensor is a thermistor
which measures the temperature of the air entering the
engine. The powertrain control module (PCM) applies 5
volts through a pull–up resistor to the IAT sensor. When
the intake air is cold, the sensor resistance is high and the
PCM will monitor a high signal voltage on the IAT signal
circuit. If the intake air is warm, the sensor resistance is
lower causing the PCM to monitor a lower voltage.
Diagnostic Trouble Code P0113 will set when the PCM
detects an excessively high signal voltage on the intake
air temperature sensor signal circuit. DTC P0113 is a
Type A Code.
Conditions for Setting the DTC
D
The engine has been running for over 240 seconds.
D
Vehicle speed is less than 32 km/h (20 mph).
D
ECT signal temperature is above 60
°
C (140
°
F).
D
Mass air flow is less than 20g/second.
D
IAT signal voltage almost 5 volts which indicates an
intake air temperature less than –39
°
C (–38
°
F) for a
total of 12.5 seconds over a 25–second period.
The above condition are met for 100 test failures within a
200 test sample (125 msec/test)
Action Taken When the DTC Sets
D
The PCM will illuminate the malfunction indicator lamp
(MIL) the first time the fault is detected.
D
The PCM will use a default IAT valve based on PCM
inputs and engine run time.
D
The PCM will store conditions which were present
when the Diagnostic Trouble Code was set as Freeze
Frame and in the Failure Records data.
Conditions for Clearing the MIL/DTC
D
The PCM will turn the MIL OFF on the third consecutive
trip cycle during which the diagnostic has been run and
the fault condition is no longer present.
D
A history Diagnostic Trouble Code P0113 will clear
after 40 consecutive warm–up cycles have occurred
without a fault.
D
Diagnostic Trouble Code P0113 can be cleared by
using the Scan Tool’s ”Clear Info” function.
Diagnostic Aids
Check for the following conditions:
D
Poor connection at PCM – Inspect harness connectors
for backed–out terminals, improper mating, broken
locks, improperly formed or damaged terminals, and
poor terminal–to–wire connection.
D
Damaged harness – Inspect the wiring harness for
damage, shorts to ground, shorts to battery positive,
and open circuits. If the harness appears to be OK,
observe the IAT display on the Tech 2 while moving
connectors and wiring harnesses related to the IAT
sensor. A change in the IAT display will indicate the
location of the fault.
6E1–131
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
If Diagnostic Trouble Code P0113 cannot be duplicated,
the information included in the Failure Records data can
be useful in determining vehicle mileage since the
Diagnostic Trouble Code was last set.
Test Description
Number(s) below refer to the step number(s) on the
Diagnostic Chart:
2.Verifies that the fault is present.
3.If Diagnostic Trouble Code P0113 can be repeated
only by duplicating the Failure Records conditions,
refer to the ”Temperature vs. Resistance Values”
table.
The table may be used to test the IAT sensor at
various temperatures to evaluate the possibility of a
”shifted” sensor that may be open above or below a
certain temperature. If this is the case, replace the
IAT sensor. If the IAT sensor appears to be OK, the
fault is intermittent; refer to Diagnostic Aids.
Intake Air Temperature Sensor
°
C
°
F
OHMS
Temperature vs. Resistance Values (approximate)
100
212
177
80
176
332
60
140
667
45
113
1188
35
95
1802
25
77
2796
15
59
4450
5
41
7280
–5
23
12300
–15
5
21450
–30
–22
52700
–40
–40
100700
DTC P0113 Intake Air Temperature (IAT) Sensor Circuit High Input
Step
Action
Value(s)
Yes
No
1
Was the ”On–Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to OBD
System
Check
2
Ignition ON, engine OFF. Observe the ”Intake Air
Temp” display on the Tech 2.
Is the ”Intake Air Temp” below the specified value?
5V –38
°
C
(–36
°
F)
Go to Step 4
Go to Step 3
3
1. Ignition ON, engine OFF.
2. Review and record Tech 2 Failure Records data
parameters.
3. Operate the vehicle within Failure Records
conditions as noted.
4. Using a Tech 2, monitor “Diagnostic Trouble Code”
info for Diagnostic Trouble Code P0113.
Does the Tech 2 indicate Diagnostic Trouble Code
P0113 failed?
—
Refer to Test
Description
Refer to
Diagnostic
Aids
4
1. Ignition OFF.
2. Disconnect the IAT sensor electrical connector.
3. Jumper the IAT signal circuit and the sensor ground
circuit together at the IAT sensor harness
connector.
4. Ignition ON.
5. Observe the ”Intake Air Temp” display on the Tech
2.
Is the ”Intake Air Temp” at the specified value?
0V 140
°
C
(284
°
F)
Go to Step 6
Go to Step 5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст