Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1322
6E1–364
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
DIAGNOSTIC TROUBLE CODE (DTC)
P1627 PCM A/D CONVERSION MALFUNCTION
014RX002
Circuit Description
The Powertrain Control Module (PCM) monitors the 5 volt
reference signal when the Ignition is ON. If the PCM
senses an Analog to Digital (A/D) conversion error within
the PCM, then DTC P1627 will set. DTC P1627 is a type A
code.
Conditions for Setting the DTC
D
Engine is running.
D
Any A/D DTC’s set.
Action Taken When the DTC Sets
D
The PCM will illuminate the Malfunction Indicator Lamp
(MIL) the first time the fault is detected.
D
The PCM will store the conditions that were present
when the DTC was set as Freeze Frame and in Failure
Records.
Conditions for Clearing the MIL/DTC
D
The PCM will turn OFF the MIL on the third consecutive
trip without a reported failure.
D
A History DTC will clear after 40 consecutive trips
without a reported failure.
D
The DTC can be cleared using the Scan Tool’s ”Clear
Info” function.
Diagnostic Aids
D
Poor connections, or a damaged harness – Inspect the
harness connectors for: backed–out terminals,
improper mating or damaged terminals. Also, check for
open circuits, shorts to ground, and shorts to voltage.
6E1–365
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
DTC P1627 PCM A/D Conversion Malfunction
Step
Action
Value(s)
Yes
No
1
Was the ”On–Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to OBD
System
Check
2
1. Ignition ON, Engine OFF.
2. Review and record Tech 2 Failure Records data,
then clear the DTCs.
3. Operate the vehicle within the Failure Records
conditions as noted.
4. Using the Tech 2, monitor ”DTC” info for DTC
P1627.
Does the Tech 2 indicate DTC P1627 ”Ran and
Passed?”
—
Refer to
Diagnostic
Aids
Go to Step 3
3
Check the suspect 5 volt reference circuit(s) for the
following conditions:
D
A short to ground
D
An open circuit
D
A short to voltage
Was the problem found?
—
Verify repair
Go to Step 4
4
Replace the PCM.
IMPORTANT: The replacement PCM must be
programmed. Refer to On–Vehicle Service in
Powertrain Control Module and Sensors for
procedures.
And also refer to latest Service Bulletin.
Check to see if the Latest software is released or not.
And then Down Load the LATEST PROGRAMMED
SOFTWARE to the replacement PCM.
Verify repair.
—
—
—
6E1–366
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
DIAGNOSTIC TROUBLE CODE (DTC) P1635 5 VOLT REFERENCE VOLTAGE
CIRCUIT MALFUNCTION
060R100046
Circuit Description
The Powertrain Control Module (PCM) monitors the 5 volt
reference signal when the Ignition is ON. If the PCM
senses the 5 volt reference signal circuit is above 5.12
volts or below 4.88 volts, then DTC P1635 will set. DTC
P1635 is a type A code.
Conditions for Setting the DTC
D
Ignition voltage is greater than 6.3 volts.
The above mentioned conditions are met and one of the
following two conditions are met for 40 test failures within
80 test samples while 125 msec.
D
PCM senses the 5 volt reference signal circuit is above
5.12 volts.
OR
D
PCM senses the 5 volt reference signal circuit is below
4.88 volts.
Action Taken When the DTC Sets
D
The PCM will illuminate the Malfunction Indicator Lamp
(MIL) the first time the fault is detected.
D
The PCM will store the conditions that were present
when the DTC was set as Freeze Frame and in Failure
Records.
Conditions for Clearing the MIL/DTC
D
The PCM will turn OFF the MIL on the third consecutive
trip without a reported failure.
D
A History DTC will clear after 40 consecutive trips
without a reported failure.
D
The DTC can be cleared using the Scan Tool’s ”Clear
Info” function.
Diagnostic Aids
Poor connections, or a damaged harness – Inspect the
harness connectors for: backed–out terminals, improper
mating or damaged terminals. Also, check for open
circuits, shorts to ground, and shorts to voltage.
6E1–367
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
DTC P1635 5 Volt Reference Voltage Circuit Malfunction
Step
Action
Value(s)
Yes
No
1
Was the ”On–Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to OBD
System
Check
2
1. Ignition ON, Engine OFF.
2. Review and record Tech 2 Failure Records data,
then clear the DTCs.
3. Operate the vehicle within the Failure Records
conditions as noted.
4. Using the Tech 2, monitor ”DTC” info for DTC
P1635.
Does the Tech 2 indicate DTC P1635 ”Ran and
Passed?”
—
Refer to
Diagnostic
Aids
Go to Step 3
3
Check the suspect 5 volt reference circuit(s) for the
following conditions:
D
A short to ground
D
An open circuit
D
A short to voltage
Was the problem found?
—
Verify repair
Go to Step 4
4
Replace the PCM.
IMPORTANT: The replacement PCM must be
programmed. Refer to On–Vehicle Service in
Powertrain Control Module and Sensors for
procedures.
And also refer to latest Service Bulletin.
Check to see if the Latest software is released or not.
And then Down Load the LATEST PROGRAMMED
SOFTWARE to the replacement PCM.
Verify repair.
—
—
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст