Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 498
EXTERIOR/INTERIOR TRIM
8J–11
15. Remove the upper rear pillar trim cover (5).
D
Pull the trim cover at the six clip positions (6) from
the body panel.
643R200007
16. Remove the assist grip (1) (Front & Rear).
D
Pull the assist grip downword.
D
Remove the caps and fixing bolts.
743R200001
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
1. Tighten the seat belt anchor bolt to the specified
torque.
Torque: 39 N·m (29 lb ft)
8J–12
EXTERIOR/INTERIOR TRIM
Headlining
Parts Location
666R200001
Legend
(1) Interior Trim Panels
(2) Headlining (Without Sunroof)
(3) Clip
(4) Luggage Room Light
(5) Assist Grip
(6) Headlinng (With Sun Roof)
(7) Sunroof Finisher (With Sunroof)
(8) Overhead Console/Sunroof Switch (With
Sunroof)
(9) Dome Light
(10) Overhead Console (Without Sunroof)
(11) Sunvisors
(12) Sunvisor Holder
Removal
1. Disconnect the battery ground cable.
2. Remove the interior trim panels.
D
Refer to
Interior Trim Panels in this section.
3. Remove the dome light.
D
Remove the dome light lens and the fixing screws.
D
Disconnect the dome light connectors.
EXTERIOR/INTERIOR TRIM
8J–13
4. Remove the luggage room light.
D
Remove the luggage room light lens (1) and the
fixing screw.
D
Disconnect the luggage room light connector.
825R200030
5. Remove the overhead console/sunroof switch (With
sunroof).
D
Refer to
Overhead Console in this section.
6. Remove the overhead console (without sunroof).
7. Remove the sunvisors.
D
Remove the fixing screws and pull out the sunvisor
holder (1) to remove it.
D
Disconnect the vanity mirror illumination connector.
743R200003
8. Remove the sunroof finisher (With sunroof).
9. Remove the headlining.
D
Remove the four headlining fixing clips.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Install the headlining so that the fixing clips will not
come off.
2. To install the sunroof finisher (1), first fit it in at one
place with the headlining (3) close to the sunroof
frame (2), then install the entire finisher tightly by
hitting it with a plastic hammer, not allowing it to move
up.
665RW003
8J–14
EXTERIOR/INTERIOR TRIM
Overhead Console
Parts Location (W/O Sunroof)
743R200005
Legend
(1) Overhead Console Bracket
(2) Harness Connector
(3) Head Lining
(4) Room Mirror
(5) Overhead Console Assembly
(6) Front Door Finisher
(7) Front Assist Grip
Removal
1. Disconnect the battery ground cable.
2. Remove the overhead console assembly.
D
Open the lid and remove the two screws.
D
Disconnect the harness connector.
3. Remove the sunvisor and sunvisor holder. (right and
left)
4. Remove the front assist grip. (right and left)
5. Remove the front piller trim cover.
6. Remove the front door finisher.
D
Remove the upper side of door finisher.
7. Remove the interior mirror.
D
Refer to
Interior Mirror in this section.
8. Remove the overhead console bracket.
D
Remove the two screws.
Installation
To install, follow the removal steps in the reverse order.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст