Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 588
3C–16
FRONT SUSPENSION
Installation
1. Install fulcrum pin.
2. Install bushing by using installer J–29755 and
J–39376.
901RW049
901RW050
3. Install plate.
4. Install nut and tighten fulcrum pin nut finger–tight.
NOTE: Torque fulcrum pin nut after adjusting buffer
clearance.
Buffer clearance: 20 mm (0.79 in)
Torque: 108 N·m (80 lb ft)
450RS012
5. Install upper control arm assembly with the fulcrum
pin projections turned inward.
450RS013
Legend
(1) Projection
(2) Outward
FRONT SUSPENSION
3C–17
6. Install the caster shims(2) between the chassis frame
and fulcrum pin.
7. Install the camber shims(1) between the chassis
frame and fulcrum pin.
450RS014
8. Install nut assembly.
9. Install bolt and plate, then tighten the bolt to the
specified torque.
Torque: 152 N·m (112 lb ft)
10. Install upper ball joint and tighten it to the specified
torque.
Torque: 57 N·m (42 lb ft)
11. Install nut and cotter pin then tighten the nut to the
specified torque, with just enough additional torque to
align cotter pin holes. Install new cotter pin.
Torque: 98 N·m (72 lb ft)
12. Install speed sensor cable.
3C–18
FRONT SUSPENSION
Lower Control Arm
Lower Control Arm and Associated Parts
450R200010
Legend
(1) Nut and Washer, Front
(2) Bush, Front
(3) Bolt, Front
(4) Nut and Washer, Rear
(5) Bush, Rear
(6) Bolt, Rear
(7) Bolt, Lower Ball Joint
(8) Bolt, Torsion Bar Arm
(9) Torsion Bar Arm and Nut
(10) Torsion Bar
(11) Lower Control Arm
(12) Lower Ball Joint and Nut
(13) Shock Absorber, Bolt Washer and Nut
(14) Stabilizer Link, Washer and Nut
Removal
1. Raise the vehicle and support the frame with suitable
safety stands.
2. Remove wheel and tire assembly. Refer to Wheel
Replacement in this section.
3. Remove the outer track rod from the knuckle. Refer to
Steering Linkage in Steering section.
4. Remove the retaining ring from the front axle driving
shaft to release the shaft from hub. Refer to Front Hub
and Disc in Driveline/Axle section.
5. Support lower control arm with a jack.
6. Remove front nut and washer.
FRONT SUSPENSION
3C–19
7. Remove rear nut and washer.
8. Remove torsion bar, refer to Torsion Bar
Replacement in this section.
9. Remove torsion bar arm.
10. Disconnect the stabilizer link at the lower control arm.
11. Remove the shock absorber lower end from the lower
control arm.
12. Remove the lower ball joint from the lower control
arm.
13. Remove front bolt.
14. Remove rear bolt.
15. Remove lower control arm.
16. Remove torsion bar arm bolt.
17. Remove lower ball joint bolt.
18. Remove front bushing by using remover J–36833.
901RW034
901RW035
19. Remove rear bushing by using remover J–36834.
901RW051
901RW052
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal conditions are
found through inspection.
Check the following parts:
D
Lower control arm
D
Bushing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст