Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 134
4C–36
DRIVE SHAFT SYSTEM
Rear Propeller Shaft
Rear Propeller Shaft and Associated Parts
401R200002
Legend
(1) Bolt, Nut and Washer (Transfer Side)
(2) Rear Propeller Shaft
(3) Bolt, Nut and Washer (Rear Axle Side)
Removal
1. Raise the vehicle on a hoist.
NOTE: Apply alignment marks on the flange at the rear
propeller shaft both front and rear side.
2. Remove transfer side bolt, nut and washer (except
spline yoke type).
3. Remove rear axle side bolt, nut and washer.
4. Remove rear propeller shaft.
NOTE: Plug the hole of the transmission rear end to
prevent oil leakage (spline yoke type only).
Installation
NOTE: Never install the shaft assembly backwards.
Never insert bar between yoke lugs when tightening or re-
moving bolts.
Completely remove the dust or foreign matter from the
connecting surface of flange coupling on each end of the
propeller shaft.
1. Align the mark which is applied at removal.
2. Install rear propeller shaft and tighten the bolts to the
specified torque.
Torque: 63 N·m(46 lb ft)
4C–37
DRIVE SHAFT SYSTEM
Slip Joint Disassembly
401RX00001
Legend
(1) Spline Yoke and Universal Joint Assembly
(2) Clamp
(3) Boot
(4) Clamp
(5) Tube and Universal Joint Assembly
1. Lay the shaft horizontally on a bench and secure.
2. Indicate the original assembled position by marking
the phasing of the shaft prior to disassembly.
3. Using the flat blade of a screwdriver, pry the loose end
of the boot clamp upwards and away from the
propeller shaft boot. Be careful not to damage the
boot.
4. When boot clamps becomes loose, remove by hand.
5. Repeat for the other boot clamp.
6. Remove the slip yoke assembly from the driveshaft,
by securing the boot with one hand and pulling on the
slip yoke.
7. Remove the boot from the shaft assembly.
4C–38
DRIVE SHAFT SYSTEM
Universal Joint Disassembly
401RX00007
Legend
(1) Spline Yoke
(2) Spider
(3) Propeller Shaft Assembly
(4) Spider
(5) Flange Yoke
(6) Bearing
(7) Snap Ring
(8) Flange Yoke
NOTE: Aluminum is softer than steel. Care must be
taken not to remove excessive material or damage
bearing holes.
If the vehicle has aluminum tube type propeller shaft,
flange yoke, boot kit, journal kit can be replaced. If other
parts are damaged, replace propeller shaft assembly.
4C–39
DRIVE SHAFT SYSTEM
1. Apply alignment marks on the yokes of the universal
joint, then remove the snap ring.
401RW024
If the snap ring is stuck in position, remove paint from
the hole in the yoke or tap around the edge of the
bearing lightly with a soft drift.
401RW025
2. Set the yoke in the arbor press with a piece of tube
stock beneath it.
Place a solid plug on the upper bearing and press it
through to release the lower bearing.
401RW027
3. If the bearing will not pull out by hand after pressing,
tap the base of the lug near the bearing to dislodge it.
4. To remove the opposite bearing, turn the yoke over
and straighten the spider in the open spider hole.
Then carefully press on the end of the spider so the
remaining bearing moves straight out of the bearing
spider hole. If the spider or bearing are cocked, the
bearing will score the walls of the spider hole and ruin
it.
401RW026
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст