Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 231
6C–4
ENGINE FUEL (6VE1 3.5L)
Fuel Filter
Removal
CAUTION: When repair to the fuel system has been
completed, start engine and check the fuel system
for loose connection or leakage. For the fuel system
diagnosis, see Section “Driveability and Emission”.
1. Disconnect battery ground cable.
2. Remove Fuel filler cap(1).
140R100023
Legend
(1) Fuel Filler Cap
(2) Receive Rubber Drain
3. Disconnect fuel hoses(1) from fuel filter on both
engine side and fuel tank side.
4. Fuel filter fixing bolt(2).
D
Remove the fuel filter fixing bolt(2) on fuel filter
holder.
5. Remove fuel filter(3).
041RW003
Legend
(1) Fuel Hose
(2) Fuel Filter Fixing Bolt
(3) Fuel Filter
Inspection
1. Replace the fuel filter if the fuel leaks from fuel filter
body or if the fuel filter body itself is damaged.
2. Replace the filter if it is clogged with dirt or sediment.
3. Check clogged drain port of the receive rubber by the
foreign material, repair or clear if found clog it.
6C–5
ENGINE FUEL (6VE1 3.5L)
Installation
1. Install the fuel filter in the proper direction.
2. Install fuel filter holder fixing bolt.
3. Connect fuel hoses on engine side(1) and fuel tank
side(2).
041RW001
4. Install fuel filler cap
5. Connect the battery ground cable.
Inspection
After installation, start engine and check for fuel leakage.
In–Tank Fuel Filter
The filter is located on the lower end of fuel pickup tube in
the fuel tank. The fuel filter prevents dirt and water the fuel
system not unless the filter is submerged in water. The
fuel filter is maintenance free, that requires no
maintenance. Excess water and sediment in the tank
restricts fuel supply to the engine, resulting in engine stall.
If this happens, the fuel tank would need to be cleaned
thoroughly.
Fuel Pump Flow Test
If reduction of fuel supply is suspected, perform the
following checks.
1. Make sure that there is fuel in the tank.
2. With the engine running, check the fuel feed pipe and
hose from fuel tank to injector for evidence of
leakage. Retighten, if pipe or hose connection is
loose. Also, inspect bent or kink fuel pipes and hoses.
3. Insert the hose from fuel feed pipe into a clean
container, and check for fuel pump flow rate.
4. Connect the pump relay terminals with a jumper
wire(1) as shown and start the fuel pump to measure
delivery.
140R200003
CAUTION: Never generate sparks when connecting
a jumper wire.
Delivery Times
Delivery
15 seconds
0.38 liters minimum
If the measure value is out of standard, conduct the
pressure test.
Pressure test
For the pressure test to the fuel system, see Section 6E
“Fuel Control System”.
6C–6
ENGINE FUEL (6VE1 3.5L)
Fuel Pump
Fuel Pump and Associated Parts
140R200008
Legend
(1) Fuel Feed Port
(2) Fuel Tube/Quick Connector
(3) Fuel Return Port
(4) Fuel Pump and Sender (FPS) Assembly
(5) Connector; Fuel Feed Pump
(6) Connector; Fuel Tank Pressure Sensor
(7) Retainer (Fuel Pump Lock)
(8) Fuel Tank Assembly
(9) Seal; Fuel Pump
Removal
CAUTION: When repair to the fuel system has been
completed, start engine and check the fuel system
for loose connection or leakage. For the fuel system
diagnosis, see Section “Driveability and Emission”.
1. Remove fuel tank assembly(8). Refer to “Fuel Tank
Removal” in this section.
2. Remove Fuel Tube/Quick Connector (2).
NOTE: Refer to “Fuel Tube/Quick Connector Fittings” in
this section when performing any repairs.
6C–7
ENGINE FUEL (6VE1 3.5L)
3. Remove the retainer (7) with tool J–39765 and
remove the fuel pump and sender (FPS) assembly
(4).
140R200007
NOTE: After removing pump assembly (4), cover fuel
tank to prevent any dust entering.
Installation
1. Install FPS assembly(4) with retainer (7) and new
seal; fuel pump (9) by J–39765.
2. Install Fuel Tube/Quick Connector (2).
NOTE: Refer to “Fuel Tube/Quick Connector Fittings” in
this section when performing any repairs.
3. Install fuel tank assembly(8). Refer to “Fuel Tank
Installation”.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст