Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 756
6E–48
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
9. Select F2: Up Shift Lamp
060RY00076
10. Push “On” soft key.
11. Make sure Lamp illuminates.
12. If Lamp illuminates, the Lamp is operating correctly.
13. Select F2:Low Fuel Lamp
060RY00092
14. Push “On” soft key.
15. Make sure Lamp illuminates.
16. If Lamp illuminates, the Lamp is operating correctly.
17. Select F3:Reduced Power Lamp
060RY00077
18. Push “On” soft key.
19. Make sure Lamp illuminates.
20. If Lamp illuminates, the Lamp is operating correctly.
21. Select F5:Cruise Control Lamp
060RY00078
22. Push “On” soft key.
23. Make sure Lamp illuminates.
24. If Lamp illuminates, the Lamp is operating correctly.
6E–49
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Relays Test
This test is conducted to check Fuel Pump Relay and A/C
Clutch for proper operation.
Tech 2 must be used for this test.
Test Procedure:
1. Connect Tech 2 to the vehicle DLC.
2. Ignition SW is “On”.
3. Select F3: Miscellaneous Test in the Application
Menu.
060R100078
4. Select F1:Relay Test in the Miscellaneous Test.
060RY00081
5. Select F0:Fuel Pump Relay.
060RX021
6. Push “On” soft key.
060RY00093
7. Control Fuel Pump Relay and check data list.
8. If the data list changes, the Fuel Pump Relay is
normal.
9. Select F1:A/C Clutch Relay.
10. Run the Engine at idle.
6E–50
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
11. Turn on Air Conditioning.
060RY00094
12. Turn “On” and “Off” A/C Switch.
13. Contol A/C Clutch Relay and check data list.
14. If the data list changes, the Fuel Pump Relay is
normal.
EVAP Test
This test is conducted to check EVAP system for its power
operation.
Tech 2 must be used for this test.
Test Procedure:
1. Connect Tech 2 to the vehicle DLC.
2. Run the Engine at idle.
3. Select F3: Miscellaneous Test in the Application
Menu.
060R100078
4. Select F2: EVAP Test in the Miscellaneous Test.
060RY00082
5. Select F0: Purge Solenoid.
060RX025
6E–51
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
6. Push “Decrease” or “Increase” soft key.
060RY00095
7. Control EVAP Purge Solenoid and check a data list.
8. If the data list changes, the Purge Solenoid is normal.
9. Turn engine off, turn ignition SW “On”.
10. Select F1:EVAP Vent Solenoid.
060RX025
11. Push “On” or “Off” soft key.
060RY00096
12. Control EVAP Vent Solenoid and check data list.
13. If the data list changes, the EVAP Vent Solenoid is
normal.
Fuel System Test
This test is conducted check Fuel system for proper
operation.
Tech 2 must be used for this test.
Test Procedure:
1. Connect Tech 2 to the vehicle DLC.
2. Ignition SW is “On”.
3. Select F3: Miscellaneous Test in the Application
Menu.
060R100078
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст