Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 46
2A–30 POWER–ASSISTED STEERING SYSTEM
Removal
To remove the connector, hold the cover insulator(1) and
pull it. The cover insulator slides and lock will be released.
Do not hold the socket insulator(2).
827RW028
Installation
To install the connector, hold the soket insulator(1) and
insert it. The cover insulator slides and connector will be
locked.
Do not hold the cover insulator(2).
827RW027
POWER–ASSISTED STEERING SYSTEM
2A–31
Inflator Module
Inflator Module and Associated Parts
827RW071
Legend
(1) Horn Lead
(2) SRS Connector
(3) Fixing Bolt
(4) Inflator Module
Removal
1. Turn the steering wheel so that the vehicle’s wheels
are pointing straight ahead.
2. Turn the ignition switch to “LOCK”.
3. Disconnect the battery “–” terminal cable, and wait at
least 5 minutes.
4. Disconnect the yellow 2-way SRS connector located
under the steering column.
5. Loosen the inflator module fixing bolt from behind the
steering wheel assembly using a TORX
driver or
equivalent until the inflator module can be released
from steering assembly .
827RW070
2A–32 POWER–ASSISTED STEERING SYSTEM
6. Disconnect the yellow 2-way SRS connector and
horn lead located behind the inflator module.
827RW073
7. Remove inflator module.
Inspection and Repair
WARNING: THE INFLATOR MODULE SHOULD
ALWAYS BE CARRIED WITH THE TRIM COVER
AWAY FROM YOUR BODY AND SHOULD ALWAYS
BE LAID ON A FLAT SURFACE WITH THE
URETHANE SIDE UP. THIS IS NECESSARY
BECAUSE FREE SPACE IS PROVIDED TO ALLOW
THE AIR CUSHION TO EXPAND IN THE UNLIKELY
EVENT OF ACCIDENTAL DEPLOYMENT.
OTHERWISE, PERSONAL INJURY MAY RESULT .
827RW072
The inflator module consists of a cover, air bag, inflator,
and retainer. Inspect the inflator module mainly for the
following:
D
Check for holes, cracks, severe blemishes and
deformation on the cover.
D
Check that the retainer is not deformed.
D
Check for defects such as damage and breakage in
the lead wire for the igniter.
Replace the inflator module if a defect is found during
inspection.
Installation
1. Install inflator module.
2. Support the module and carefully connect the module
connector and horn lead.
NOTE: Pass the lead wire through the tabs on the plastic
cover (wire protector) of inflator to prevent lead wire from
being pinched.
3. Tighten bolts to specified torque.
Torque: 9 N·m (78 lb in)
4. Connect the yellow 2-way SRS connector located
under the steering column.
5. Connect the battery “–” terminal cable.
6. Set ignition to “ON” while watching warning light.
Light should flash 7 times and then go off. If lamp
does not operate correctly, refer to
Restraints section.
POWER–ASSISTED STEERING SYSTEM
2A–33
Steering Wheel
Steering Wheel and Associated Parts
827RW069
Legend
(1) Horn Lead
(2) SRS Connector
(3) Steering Wheel
(4) Steering Wheel Fixing Nut
(5) Inflator Module
CAUTION: Once the steering column is removed
from the vehicle, the column is extremely
susceptible to damage. Dropping the column
assembly on its end could collapse the steering shaft
or loosen the slide block which maintains column
rigidity. Leaning on the column assembly could
cause the jacket to bend or deform. Any of the above
damage could impair the column’s collapsible
design. If it is necessary to remove the steering
wheel, use only the specified steering wheel puller.
Under no conditions should the end of the shaft be
hammered upon, as hammering could loosen the
slide block which maintains column rigidity.
Removal
1. Turn the steering wheel so that the vehicle’s wheels
are pointing straight ahead.
2. Turn the ignition switch to “LOCK”.
3. Disconnect the battery ground cable, and wait at least
5 minutes.
4. Disconnect the yellow 2-way SRS connector located
under the steering column.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст