Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1658
8F–74
BODY STRUCTURE
Installation
1. Rear quarter glass.
• Clean the bonding surfaces of both the glass and
the body panel.
• Be absolutely sure to apply glass primer to the
side glass.
• Be absolutely sure to apply body primer fully to
the body.
NOTE: Immediately wipe off the primer left on the body
or extruded sealant.
• Attach the fastener to the indicated position of
body with sealant as shown in the figure.
• Apply the sealant to the circumference of glass
as shown in the figure.
• Insert the location pins on glass into the panel,
push the glass against the panel, and bond them.
• Attach the molding to the body with sealant.
• Cure the bonding at a temperature of 20
°C –
30
°C (68°F – 86°F) for 24 hours.
• Check the rear quarter glass for any signs of
water leak.
2. Install the rear quarter trim panel.
BODY STRUCTURE
8F–75
Rear Quarter Glass (Resin Top)
Parts Location
641RW011
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the rear quarter glass assembly.
• Refer to Windshield in this section.
Installation
1. Use alcohol or the like to wipe clean the areas of the
resin top and glass assembly that are to be affixed
to each other.
2. Apply the primer (2) to the area of the resin top to
which the glass is to be affixed.
• Top edge (1) and bottom edge (3) primer coat
areas.
641RX002
Legend
(1) Resin Top
(2) Fastener Tape
(3) Rear Quarter Glass Assembly
(4) Dam Seal
(5) Adhesive
(6) Body Panel
(7) Weather Strip
(8) Clip
8F–76
BODY STRUCTURE
3. Stick the fasteners tape to the body in the specified
locations.
4. Install the rear quarter glass assembly (1).
• Apply the primer (4) to the rear quarter glass as
shown in the figure.
• Stick the dam seal (2) in place and then apply
adhesive (3), as shown in the figure.
• Allow a 20mm (0.79 in) overlap at the ends of the
adhesive.
• Insert the glass clips into the hole in the panel
and then push the glass against the panel to affix
it in place.
641RX001
BODY STRUCTURE
8F–77
Side Window Glass (SWB)
Parts Location
641RX003
EndOFCallout
Removal
1. Remove the quarter trim cover.
• Refer to Interior Trim Panels (SWB) in Exterior/
Interior Trim section.
2. Remove the side window garnish assembly.
• Pull out the three clips to disengage them.
3. Remove the side window molding.
4. Remove the side window glass.
• Refer to Windshield in this section.
Installation
1. Install the side window glass.
• Clean the areas of the glass and body panel that
are to be affixed to each other.
• Apply the primer to the specified areas of the
glass and body panel.
• Stick the spacer and fastener tape in place in the
specified locations.
• Apply the adhesive to the entire circumference of
the glass, as shown in the figure.
• Insert the glass clips into the panel and then push
the glass against the panel to affix it in place.
• Wipe away any adhesive that oozes out around
the edges.
2. Install the side window garnish assembly.
• Install it securely and inspect for snug fit.
3. Install the side window molding.
• Insert it securely and inspect for snug fit.
• Make sure that there is no water leakage from the
side window glass.
4. Install the quarter trim cover.
Legend
(1) Spacer
(2) Primer Coating Area on Glass Side
(3) Side Window Molding
(4) Adhesive
(5) Clip
(6) Side Window Glass
(7) Fastener Tape
(8) Side Window Garnish Assembly
(9) Body Panel
(10) Primer Coating Area on Body Side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст