Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1732
REAR SUSPENSION
3D–5
Coil Spring
Coil Spring and Associated Parts
460R200004
EndOFCallout
Removal
1. Raise the vehicle and support the frame with
suitable safety stands.
2. Support the rear axle case with a jack.
3. Disconnect brake hose at the crossmember.
4. Remove breather hose.
5. Remove upper link fixing bolt, nut and rubber plate
on the rear axle case (left-side only).
6. Disconnect the stabilizer bar at the stabilizer link.
7. Remove the shock absorber from the axle case.
8. Remove spring insulator.
9. Remove the insulator and coil spring while lowering
the rear axle case.
CAUTION: Be sure not to let the brake hose,
parking brake cable, and breather hose extend to
their full length.
Legend
(1) Stabilizer Bar
(2) Upper Link Fixing Bolt and Nut
(3) Rubber Plate
(4) Coil Spring
(5) Insulator
(6) Shock Absorbar
(7) Breather Hose
3D–6
REAR SUSPENSION
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
Check the following parts:
• Coil spring
• Insulator
Installation
1. Install coil spring and make sure that the coil spring
is installed in the proper position. Paint mark(1)
should be downward.
460RW001
2. Fit the end of the coil spring to the coil spring seat
and mount the coil spring on the rear axle case.
460RW004
3. Install the insulator on the coil spring. Jack up the
axle case gently with the top of the coil spring set to
the spring seat on the frame side.
460RW013
4. Install shock absorber and tighten the nut lightly,
then retighten it to the specified torque after the
vehicle is at curb height.
NOTE: When mounting shock absorber, be sure not to
use grease on bushings or any other nearby part.
Torque: 78 N·m (58 lb ft)
5. Install stabilizer bar at the stabilizer link.
Torque: 31 N·m (23 lb ft)
6. Install upper link with rubber plate and tighten fixing
bolt.
Torque: 137 N·m (101 lb ft)
7. Install breather hose.
8. Connect brake hose and bleed the brake system.
Refer to Bleeding the Brake Hydraulic System in
Brake section.
REAR SUSPENSION
3D–7
Shock Absorber
Shock Absorber and Associated Parts
461RW001
EndOFCallout
Removal
1. Remove shock absorber fixing nut, bush and
washer (upper side).
2. Remove shock absorber fixing nut and washer
(lower side).
3. Remove shock absorber.
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
Check the following parts:
• Shock absorber
• Rubber bushing
NOTE: When mounting rubber bushings, be sure not to
use grease on bushings or any other nearby part.
Installation
1. Install shock absorber. When mounting shock
absorber, be sure not to use grease on bushings or
any other nearby part.
2. Install nut and washer (lower side), then tighten the
nut lightly. Retighten to the bolt and nut specified
torque after the vehicle is at curb height.
Torque: 78 N·m (58 lb ft)
3. Install nut, bush and washer (upper side), then
tighten the nut lightly. Retighten to the nut specified
torque after the vehicle is at curb height.
Torque: 20 N·m (14 lb ft)
Legend
(1) Nut, Bush and Washer
(2) Shock Absorber
(3) Nut and Washer
3D–8
REAR SUSPENSION
Trailing Link
Trailing Link and Associated Parts
460RW005
EndOFCallout
Removal
1. Remove the parking brake cable from the trailing
link.
2. Remove the trailing link fixing bolt, nut and
protector.
3. Remove trailing link.
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
1. Trailing link
2. Rubber bushing
• Remove the rubber bushing by using remover J–
39214.
901RW058
Legend
(1) Bolt and Nut (Axle side)
(2) Protector (Left side only)
(3) Bolt (Frame side)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст