Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1248
6E1–68
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
Injector Coil Test Procedure (Steps 1–6)
And Injector Balance Test Procedure (Steps 7–11)
R262001
CYLINDER
1
2
3
4
1st Reading
296 kPa
(43psi)
296 kPa
(43psi)
296 kPa
(43psi)
296 kPa
(43psi)
2nd Reading
131 kPa
(19 psi)
117 kPa
(17 psi)
124 kPa
(18 psi)
145 kPa
(21 psi)
Amount of Drop (1st Reading–2nd
Reading
165 kPa
(24 psi)
179 kPa
(26 psi)
172 kPa
(25 psi)
151 kPa
(22 psi)
Av. drop = 166 kPa/24 psi +/–10
kPa/1.5 psi = 156 – 176 kPa or 22.5
– 25.5 psi
OK
Faulty, Rich
(Too Much Fuel
Drop)
OK
Faulty, Lean
(Too Little Fuel
Drop)
NOTE: These figures are examples only.
6E1–69
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
Injector Coil Test Procedure (Steps 1–6)
And Injector Balance Test Procedure (Steps 7–11)
Step
Action
Value(s)
Yes
No
1
Was the ”On–Board Diagnostic (OBD) System Check”
performed?
—
Go to
Step 2
Go to
OBD
System
Check
2
1. Turn the engine OFF.
NOTE: In order to prevent flooding of a single cylinder
and possible engine damage, relieve the fuel pressure
before performing the fuel injector coil test procedure.
2. Relieve the fuel pressure. Refer to Test Description
Number 2.
3. Connect the J 39021–5V Fuel Injector Tester to B+
and ground, and to the J39021–90 Injector Switch
Box.
4. Connect the injector switch box to the grey fuel
injector harness connector located at the front of the
EVAP canister bracket.
5. Set the amperage supply selector switch on the fuel
injector tester to the ”Coil Test” 0.5 amp position.
6. Connect the leads from the J 39200 Digital
Voltmeter (DVM) to the fuel injector tester. Refer to
the illustrations associated with the test description.
7. Set the DVM to the tenths scale (0.0).
8. Observe the engine coolant temperature.
Is the engine coolant temperature within the specified
values?
10
°
C (50
°
F)
to 35
°
C
(95
°
F)
Go to
Step 3
Go to
Step 5
3
1. Set the injector switch box to injector #1.
2. Press the ”Push to Start Test” button on the fuel
injector tester.
3. Observe the voltage reading on the DVM.
IMPORTANT: The voltage reading may rise during the
test.
4. Record the lowest voltage observed after the first
second of the test.
5. Set the injector switch box to the next injector and
repeat steps 2, 3, and 4.
Did any fuel injector have an erratic voltage reading
(large fluctuations in voltage that did not stabilize) or a
voltage reading outside of the specified values?
5.7–6.6 V
Go to
Step 4
Go to
Step 7
4
Replace the faulty fuel injector(s). Refer to Fuel
Injector.
Is the action complete?
—
Go to
Step 7
—
6E1–70
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
Injector Coil Test Procedure (Steps 1–6)
And Injector Balance Test Procedure (Steps 7–11)
(Cont'd)
Step
No
Yes
Value(s)
Action
5
1. Set the injector switch box to injector #1.
2. Press the ”Push to Start Test” button on the fuel
injector tester.
3. Observe the voltage reading on the DVM.
IMPORTANT: The voltage reading may rise during the
test.
4. Record the lowest voltage observed after the first
second of the test.
5. Set the injector switch box to the next injector and
repeat steps 2, 3, and 4.
Did any fuel injector have an erratic voltage reading
(large fluctuations in voltage that did not stabilize) or a
voltage reading above the specified value?
9.5 V
Go to
Step 4
Go to
Step 6
6
1. Identify the highest voltage reading recorded (other
than those above 9.5 V).
2. Subtract the voltage reading of each injector from
the highest voltage selected in step 1. Repeat until
you have a subtracted value for each injector.
For any injector, is the subtracted value in step 2
greater than the specified value?
0.6 V
Go to
Step 4
Go to
Step 7
7
CAUTION: In order to reduce the risk of fire and
personal injury, wrap a shop towel around the
fuel pressure connection. The towel will absorb
any fuel leakage that occurs during the
connection of the fuel pressure gauge. Place the
towel in an approved container when the
connection of the fuel pressure gauge is
complete.
1. Connect the J 34730–1 Fuel Pressure Gauge to the
fuel pressure test port.
2. Energize the fuel pump using the Tech 2.
3. Place the bleed hose of the fuel pressure gauge into
an approved gasoline container.
4. Bleed the air out of the fuel pressure gauge.
5. With the fuel pump running, observe the reading on
the fuel pressure gauge.
Is the fuel pressure within the specified values?
296 kPa– 376
kPa (43–55
psi)
Go to
Step 8
Go to
Fuel
System
Diagnosis
8
Turn the fuel pump OFF.
Does the fuel pressure remain constant?
—
Go to
Step 9
Go to
Fuel
System
Diagnosis
6E1–71
RODEO Y22SE 2.2L ENGINE DRIVEABILITY AND EMISSION
Injector Coil Test Procedure (Steps 1–6)
And Injector Balance Test Procedure (Steps 7–11)
(Cont'd)
Step
No
Yes
Value(s)
Action
9
1. Connect the J 39021–5V Fuel Injector Tester and
J39021–90 Injector Switch Box to the fuel injector
harness connector.
2. Set the amperage supply selector switch on the fuel
injector tester to the ”Balance Test” 0.5–2.5 amp
position.
3. Using the Tech 2 turn the fuel pump ON then OFF in
order to pressurize the fuel system.
4. Record the fuel pressure indicated by the fuel
pressure gauge after the fuel pressure stabilizes.
This is the first pressure reading.
5. Energize the fuel injector by depressing the Push to
Start Test button on the fuel injector tester.
6. Record the fuel pressure indicated by the fuel
pressure gauge after the fuel pressure gauge
needle has stopped moving. This is the second
pressure reading.
7. Repeat steps 1 through 6 for each fuel injector.
8. Subtract the second pressure reading from the first
pressure reading for one fuel injector. The result is
the pressure drop value.
9. Obtain a pressure drop value for each fuel injector.
10.Add all of the individual pressure drop values. This
is the total pressure drop.
11. Divide the total pressure drop by the number of fuel
injectors. This is the average pressure drop.
Does any fuel injector have a pressure drop value that
is either higher than the average pressure drop or lower
than the average pressure drop by the specified value?
10 kPa (1.5
psi)
Go to
Step 10
Go to
OBD
System
Check
10
Re–test any fuel injector that does not meet the
specification. Refer to the procedure in step 11.
NOTE: Do not repeat any portion of this test before
running the engine in order to prevent the engine from
flooding.
Does any fuel injector still have a pressure drop value
that is either higher than the average pressure drop or
lower than the average pressure drop by the specified
value?
10 kPa (1.5
psi)
Go to
Step 11
Go to
Symptoms
11
Replace the faulty fuel injector(s). Refer to Fuel
Injector.
Is the action complete?
—
Verify repair
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст