Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1680
EXTERIOR/INTERIOR TRIM
8J–27
4. Remove the waterproof sheet (1).
• Carefully remove the waterproof sheet not to
brake it.
681R100001
5. Remove the license plate garnish asm.
• Remove the a screw on the upper side.
• Remove the two fixed nuts from the inside of the
tailgate and remove the three clips by pushing the
tip of the clips with a screwdriver.
Installation
To install, follow the removal steps in the reverse order.
Power Door Mirror System
General Description
The system consists of the starter switch, door mirror
switch, rear defogger/mirror defogger switch and door
mirrors on both sides.
When the door mirror switch is operated with the starter
switch at either “ACC" or “ON" position, the motor in the
door mirror (on either side) rotates to allow the
horizontal and vertical adjustment of mirror angles.
When the rear defogger/mirror defogger switch is turned
“ON" with the starter switch “ON", the heater of the left
and right mirrors and the tailgate glass are activated.
Door Mirror Switch
Removal
1. Disconnect the battery ground cable.
2. Remove the instrument panel lower cover (2).
Refer to the instrument panel assembly in Body
Structure section.
3. Remove the door mirror switch (1).
825RW094
Rear Defogger/Mirror Defogger Switch
Refer to the Rear Defogger/Mirror switch removal and
installation steps in Lighting System section.
Door Mirrors
Refer to Door Mirror Assembly in this section.
8J–28
EXTERIOR/INTERIOR TRIM
Power Window System
General Description
The power window system consists of power window
switches and power window motors on driver and
passenger sides and power window relay. With the
starter switch in “ON" position, the battery voltage is
supplied through power window relay to the power
window switches on driver and passenger sides.
Selection of up or down switch changes the motor
rotating direction to open or close the window.
When the power window “LOCK" switch on the driver
side is pressed, the power source for the other switches
are disconnected causing the power window operation
to seize.
Power Window Switch Driver Seat
Side
Removal
1. Disconnect the battery ground cable.
2. Remove the switch (1).
• Pull out the switch by pushing the spring with the
tip of a screwdriver.
• Disconnect the connector.
825RW080
Installation
To install, follow the removal steps in the reverse order.
Front Passenger Seat Side
Removal
1. Disconnect the battery ground cable.
2. Remove the switch (1).
• Pull out the switch by pushing the spring with the
tip of a screwdriver.
• Disconnect the connector.
825RW097
Installation
To install, follow the removal steps in the reverse order.
Rear-Left and Right Sides
Removal
1. Disconnect the battery ground cable.
2. Remove the rear door trim pad (2).
• Refer to the Rear Door Trim Pad removal steps in
Exterior/Interior Trim section.
• Disconnect the rear power window switch (1)
connector.
3. Remove the rear power window switch (1).
• Remove the switch fixing screw from the back
side of the rear door trim (2).
825RW081
EXTERIOR/INTERIOR TRIM
8J–29
825RW079
Installation
To install, follow the removal steps in the reverse order.
Power Window Motor
Driver Seat Side
Removal
1. Disconnect the battery ground cable.
2. Remove the window regulator assembly (2).
• Refer to the Window Regulator and Glass
removal steps in Body Structure section.
3. Remove the power window motor (1).
• Remove three screws.
825RW096
Installation
To install, follow the removal steps in the reverse order.
Front Passenger Seat Side
Removal and Installation
Refer to the Front Window Motor — Driver Seat side
removal and installation steps in this section.
Rear-Left Side
Removal
1. Disconnect the battery ground cable.
2. Remove the rear window regulator assembly (2).
• Refer to the Rear Window Regulator and Glass
removal steps in Body Structure section.
3. Remove the power window motor (1).
• Remove three screws.
825RW095
Installation
To install, follow the removal steps in the reverse order.
Rear-Right Side
Removal and Installation
Refer to the Rear Power Window Motor — Left Side
removal and installation steps in this section.
8J–30
EXTERIOR/INTERIOR TRIM
Main Data and Specifications
Torque Specifications
Application
N·m
lb ft
lb in
Front & Rear Seat Belt A nchor Bolts
39
29
—
Roof Rail Fixing Bolts
8
—
69
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст