Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 126
4C–4
DRIVE SHAFT SYSTEM
7. Remove hub and disc assembly.
8. Remove ABS sensor ring.
9. Remove outer bearing.
10. Remove oil seal.
11. Remove inner bearing.
12. Use a brass bar to remove the outer bearing outer
race(1), oil seal, inner bearing and inner bearing outer
race(2) from the hub.
411RS002
13. Remove bolt.
14. If necessary, replace the wheel pin in the following
manner.
D
Scribe mark(1) on hub to disc before disassembly
to insure proper assembly.
411RS003
D
Clamp hub and disc assembly in vise, using
protective pads. Remove six(6) disc-to-hub
retaining bolts.
411RS021
D
Place hub on a suitable work surface and remove
wheel studs, as required, using a hammer.
411RS004
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
Check the following parts.
D
Hub
D
Hub bearing oil seal
D
Knuckle spindle
D
Disc
D
Caliper
D
ABS sensor ring
For inspection and servicing of disc caliper and related
parts, refer to
Disc Brake in Brake section.
4C–5
DRIVE SHAFT SYSTEM
Reassembly
1. Install wheel pin.
D
Place hub on a wood workbench or a block of wood
approx. 6” by 6” to protect the wheel stud ends and
threads.
D
Install wheel stud, using a hammer.
NOTE: Be sure wheel stud is started squarely and seats
completely.
411RS005
2. Align scribe marks(1) and attach the hub to disc then
tighten the bolts to the specified torque.
Torque: 103 N·m (76 lb ft)
411RS003
3. Install inner bearing.
Install the outer race by driving it into the hub by using
installer J–36829 and grip J–8092.
411RS023
4. Install outer bearing.
Install the outer race by driving it into the hub by using
installer J–36828 and grip J-8092.
901RW056
4C–6
DRIVE SHAFT SYSTEM
5. Install oil seal by using installer J–36830 and grip
J–8092.
Apply Multipurpose grease (NLGI No. 2 or equivalent)
to the lip portion.
901RW057
6. Inatall ABS sensor ring, then tigthen the bolts to the
specified torque.
Torque: 18 N·m (13 lb ft)
7. Install hub and disc assembly.
D
Apply grease in the hub.
D
Apply wheel bearing type grease (NLGI No.2 or
equivalent) to the outer and inner bearing.
Hub
35 g (1.23 oz)
Outer bearing
10 g (0.35 oz)
Inner bearing
15 g (0.53 oz)
8. Install hub nut.
Turn the place where there is a chamfer in the tapped
hole to the outer side, then attach the nut by using
front hub nut wrench J–36827.
901RW054
Preload Adjustment
1. Tighten the hub nut to 29.4 N·m (21.7 lb ft), then
fully loosen the nut.
2. Tighten the hub nut to the value given below,
using a spring scale on the wheel pin.
Bearing Preload
New bearing and New
oil seal
19.6 – 24.5 N
(4.4 – 5.5 lb)
Used bearing and New
oil seal
11.8 – 17.7 N
(2.6 – 4.0 lb)
If the measured bearing preload is outside the
specifications, adjust it by loosening or tightening
the hub nut.
411RS011
4C–7
DRIVE SHAFT SYSTEM
9. Install lock washer and lock screw.
D
Turn the side with larger diameter of the tapered
bore to the vehicle outer side, then attach the
washer.
D
If the bolt holes in the lock plate are not aligned with
the corresponding holes in the nut, reverse the lock
plate.
D
If the bolt holes are still out of alignment, turn in the
nut just enough to obtain alignment.
D
Screw is to be fastened tightly so its head may
come lower than the surface of the washer.
411RS012
10. Install cover and gasket then tighten the cover bolt.
Torque: 59 N·m (43 lb ft)
11. Install brake caliper and tighten fixing bolt.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст