Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1741
4C–22
DRIVE SHAFT SYSTEM
Universal Joint Reassembly
1. Pack the four grease cavities of the spider with a
high quality, extreme pressure N.L.G.I. Grade 2
grease. Do not add additional grease to bearing cup
assembly.
2. Move one end of the spider to cause a trunnion to
project through the spider hole beyond the outer
machined face of the yoke lug. Place a bearing over
the trunnion diameter and align it to the spider hole.
Using an arbor press, align the trunnion to the
spider hole and place a solid plug on the upper
bearing. Press the bearing into the spider hole
enough to install snap ring.
401RW087
3. Install a snap ring.
NOTE: Be sure the snap rings are properly seated in
the grooves.
4. Repeat steps 2 and 3 to install the opposite bearing.
If the joint is stiff, strike the yoke ears with a soft
hammer to seat the bearing.
5. Align the setting marks and join the yokes.
DRIVE SHAFT SYSTEM
4C–23
Slip Joint Reassembly (6VD1 Model Only)
401RW081
EndOFCallout
1. Apply grease evenly to both the female and male
splines.
2. Apply a small amount of grease by finger to the
outer lips of the boot.
3. Slide the boot (smaller diameter side) onto the
spline yoke shaft being careful not to damage the
spline coating or boot.
4. Carefully insert the spline yoke shaft into the tube
assembly to maintain proper phasing. The spider
holes should be in line according to the marks made
prior to disassembly.
5. Position boot over tube assembly and yoke shaft in
its assembled position over boot grooves.
6. Attach boot clamps and secure using pliers.
7. Be sure clamp is properly seated and secure.
CAUTION: Use a new clamp similar to the original
clamp. Use of any other clamp may cause shaft
imbalance and/or grease leakage.
Legend
(1) Spline Yoke and Universal Joint Assembly
(2) Clamp
(3) Boot
(4) Clamp
(5) Tube and Universal Joint Assembly
4C–24
DRIVE SHAFT SYSTEM
Main Data and Specifications
General Specifications
Torque Specifications
401RX00008
2WD Model
4WD Model
Engine
Y22SE
6VD1
6VD1
Transmission
M/T
A/T
A/T
M/T
A/T
Type (See illustration)
1
2
2
2
2
Length
(between two spiders
center)
1076.4mm
(42.38in)
1106.4mm
(43.56in)
1096.7mm
(43.18in)
963.2mm
(37.92in)
774.9mm
(30.51in)
Universal joint type
Cardan type
BRAKE CONTROL SYSTEM
5–1
RODEO SPORT
BRAKE CONTROL SYSTEM
CONTENTS
Brake Control System
See 2002 Rodeo(UE) Workshop Manual
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anti–lock Brake System
See 2002 Rodeo(UE) Workshop Manual
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power–assisted Brake System
See 2002 Rodeo(UE) Workshop Manual
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brakes (4x4 Model)
See 2002 Rodeo(UE) Workshop Manual
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brakes (4x2 Model)
See 2002 Rodeo(UE) Workshop Manual
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст