Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 115
DRIVE LINE CONTROL SYSTEM (TOD)
4B2–78
Step
Action
Yes
No
1
1. Turn on the starter switch.
When the TOD switch is selected to the TOD position, is 0V
observed between terminals 30 and 47, and 43 and 47? Does the
voltage between the terminals 7 and 47, 19 and 47, and 8 and 47
comply with the TOD mode in the following table?
Go to
Step 2
Repair the TOD
switch circuit.
Go to
Step 4
2
When the TOD switch is selected to the 2H position, is 12V
observed between terminals 30 and 47, and 0V observed
between terminals 43 and 47? Does the voltage between the
terminals 7 and 47, 19 and 47, and 8 and 47 comply with the 2H
mode in the following table?
Go to
Step 3
Repair the TOD
switch circuit.
Go to
Step 4
3
When the TOD switch is selected to the 4L position, is 0V
observed between the terminal 30 and 47 and 12V observed
between the terminal 43 and 47? Does the voltage between the
terminals 7 and 47, 19 and 47, and 8 and 47 comply with the 4L
mode in the following table?
The phenomenon
is not
reproduced.
Refer to
“Trouble
intermittentry
observed”.
Repair the TOD
switch circuit.
Go to
Step 4
4
1. Check that all the parts are mounted.
Is this step complete?
Verify repair.
Go to
Step 4
Table: Indicator terminal voltage
Unit: V
TOD
switch
Terminals measured
switch
mode
Front 7
and 47
AUTO 19
and 47
Rear 8 and
47
2H
8.0
∼
14.5
8.0
∼
14.5
0
TOD
0
0
0
4L
0
8.0
∼
14.5
0
4B2–79
DRIVE LINE CONTROL SYSTEM (TOD)
Chart B–4
The TOD switch B circuit is shorted to battery.
Function of circuit
—
Fail condition
Even after the transfer mode is selected from 4L to TOD, the indicator lamp state does
not change.
Indicator lamp state
TOD switch position
TOD
DRIVE LINE CONTROL SYSTEM (TOD)
4B2–80
D04R200022
4B2–81
DRIVE LINE CONTROL SYSTEM (TOD)
Step
Action
Yes
No
1
1. Turn off the starter switch.
2. Disconnect the ECU connector (C–38).
Is the continuity established between the connector terminals
(C–38) 14 and (C–38) 19?
Go to
Step 2
Replace TOD
indicator lamp
bulb.
Go to
Step 5
2
1. Turn off the starter switch and connect the ECU connector.
2. Turn on the starter switch.
When the TOD switch is selected to the TOD position, is 0V
observed between terminals 30 and 47, and 43 and 47? Does the
voltage between the terminals 7 and 47, 19 and 47, and 8 and 47
comply with the TOD mode in the following table?
Go to
Step 3
Repair the TOD
switch circuit.
Go to
Step 5
3
When the TOD switch is selected to the 2H position, is 12V
observed between terminals 30 and 47, and 0V observed
between terminals 43 and 47? Does the voltage between the
terminals 7 and 47, 19 and 47, and 8 and 47 comply with the 2H
mode in the following table?
Go to
Step 4
Repair the TOD
switch circuit.
Go to
Step 5
4
When the TOD switch is selected to the 4L position, is 0V
observed between the terminal 30 and 47 and 12V observed
between the terminal 43 and 47? Does the voltage between the
terminals 7 and 47, 19 and 47, and 8 and 47 comply with the 4L
mode in the following table?
The phenomenon
is not
reproduced.
Refer to
“Trouble
intermittently
observed”.
Repair the TOD
switch circuit.
Go to
Step 5
5
1. Check that all the parts are mounted.
Is this step complete?
Verify repair.
Go to
Step 5
Table: Indicator terminal voltage
Unit: V
TOD
switch
Terminals measured
switch
mode
Front 7
and 47
AUTO 19
and 47
Rear 8 and
47
2H
8.0
∼
14.5
8.0
∼
14.5
0
TOD
0
0
0
4L
0
8.0
∼
14.5
0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст