Isuzu N-Series. Service manual — part 368
6A3-124 ENGINE (4HF1 / 4HF1-2 / 4HE1-TC / 4HG1 / 4HG1-T)
3) Remove the pressure plate assembly.
14. Driven Plate
Remove the driven plate with the clutch pilot align-
er.
15. Engine Control Wire
16. Engine Control Lever Assembly
17. Oil Pipe
18. Oil Filter Assembly
19. Tachometer Sensor
20. Fuel Pipe Bracket
21. Vacuum Pump Oil Pipe
22. Vacuum Pump Rubber Hose
Legend
A. Knock pin
Legend
1. Clutch pilot aligner
2. Clutch pressure plate assembly
3. Driven plate
N6A0352E
N6A0351E
N6A0425E
N6A0285E
ENGINE (4HF1 / 4HF1-2 / 4HE1-TC / 4HG1 / 4HG1-T) 6A3-125
23. Fan Belt
24. Generator
25. Engine Foot
26. Injection Pump Assembly
1) Remove the injection pump bracket bolts and
the injection pump rear bracket bolts.
2) Then remove the injection pump assembly.
27. Injection Pump Rubber Spacer
28. Idle Pulley Bracket (If equipped with A/C)
29. Heater Pipe
Legend
1. Vacuum pump oil pipe
2. Vacuum pump rubber hose
N6A0630E
N6A0631E
N6A0426E
N6A0289E
6A3-126 ENGINE (4HF1 / 4HF1-2 / 4HE1-TC / 4HG1 / 4HG1-T)
30. Water Suction Pipe
31. Oil Cooler Assembly
1) Remove the oil cooler bolts.
2) Install a oil cooler fixing bolt to the oil cooler re-
placer hole as shown in the illustration, and
tighten the bolt alternately a little at a time.
32. Fan Belt Adjust Plate
33. Generator Bracket
34. Cover
Legend
A. 4HF1-2
N6A0290E
N6A0532E
N6A0292E
N6A0293E
N6A0294E
ENGINE (4HF1 / 4HF1-2 / 4HE1-TC / 4HG1 / 4HG1-T) 6A3-127
35. Crankshaft Damper Pulley
1) Use the crankshaft stopper to prevent the
crankshaft from turning.
Crankshaft Stopper: 5-8840-2230-0
2) Loosen the damper pulley bolts and remove
the damper pulley.
36. Crankshaft Front Oil Seal
37. Crankshaft Front Slinger
Above works refer to “CRANKSHAFT FRONT OIL
SEAL” section in this manual.
38. Flywheel Assembly
1) Use the crankshaft stopper to prevent the
crankshaft from turning
Crankshaft Stopper: 5-8840-2230-0
2) Loosen the flywheel bolts in numerical order a
little at a time as shown in the illustration.
3) Remove the flywheel stopper and the flywheel
assembly.
39. Crankshaft Rear Seal
40. Crankshaft Rear Slinger
Above works refer to “CRANKSHAFT REAR OIL
SEAL” section in this manual.
41. Spacer Rubber
Remove the stiffener before removing the spacer
rubber.
42. Oil Pan
43. Oil Pump Strainer
44. Water Pump Pulley
45. Water Pump
46. Front Retainer
Install the three front retainer fixing bolts to the
front retainer replacer holes as shown in the illus-
tration, and tighten the bolts alternately a little at a
time.
N6A0427E
N6A0427E
Legend
1. Washer
2. Pilot bearing
N6A6504E
N6A0193E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст