Isuzu N-Series. Service manual — part 923
Transmission Control System (Smoother) 7A-147
11
Important:
Replacement 2-4-6-R shift solenoid valve must be
relearned.
Replace the 2-4-6-R shift solenoid valve. Refer to
Repair Instructions (Overhaul) - Gearshift Control
Box in this section.
Did you complete the replacement?
—
Go to Step 13
—
12
Important:
Replacement TCM must be programmed and
learned.
Replace the TCM. Refer to Transmission Control
Module (TCM) Replacement in this section.
Did you complete the replacement?
—
Go to Step 13
—
13
1. Reconnect all previously disconnected
harness connector(s).
2. Clear the DTCs with the Tech 2.
3. Turn OFF the ignition for 30 seconds.
4. Start the engine.
5. Operate the vehicle within the Conditions for
Running the DTC.
Did the DTC fail this ignition?
—
Go to Step 2
Go to Step 14
14
Observe the DTC Information with the Tech 2.
Are there any DTCs that you have not diagnosed?
—
Go to Diagnostic
Trouble Code (DTC)
List
System OK
Step
Action
Value(s)
Yes
No
7A-148 Transmission Control System (Smoother)
P0974 (Flash Code 71)
Circuit Description
The pulse width modulation (PWM) 2-4-6-R shift
solenoid valve is located on the gearshift control box.
The transmission control module (TCM) controls the 2-
4-6-R shift solenoid valve by duty cycle signal based on
commanded gear position. The 2-4-6-R shift solenoid is
commanded ON when the commanded gear is set to
2nd, 4th, 6th and reverse gear. When disengaging
from1st, 3rd and 5th gear, the 2-4-6-R shift solenoid is
also commanded ON. The gear shift position sensor is
used to detect the shift side lever position feedback for
the shift solenoid valves movement. The TCM uses the
gear shift position sensor to determine the current gear
position with a combination of the gear select position
sensor. If the TCM detects a low voltage condition on
the 2-4-6-R shift solenoid valve monitor circuit when the
solenoid valve is commanded ON, this DTC will set.
Condition for Running the DTC
• DTC P0889 is not set.
• The ignition switch is ON.
• The ignition voltage is more than 20 volts.
• The emergency switch is OFF.
• The gearshift control box relay is commanded ON.
Condition for Setting the DTC
• The TCM detects a low voltage condition on the 2-
4-6-R shift solenoid valve monitor circuit when the
solenoid valve is commanded ON.
Action Taken When the DTC Sets
• The TCM illuminates the transmission warning
lamp when the diagnostic runs and fails.
• The TCM intermittently sounds buzzer when the
diagnostic runs and fails.
• The TCM commands OFF gearshift control box
relay.
• The TCM inhibits gearshift control and holds gear
position when the diagnostic runs and fails.
• The TCM inhibits gear select & shift position
learning and half-clutch learning.
Condition for Clearing the DTC
• The TCM turns OFF the transmission warning
lamp when the diagnostic runs and does not fail at
next ignition cycle
• The TCM stops the buzzer when the diagnostic
runs and does not fail at next ignition cycle.
• A current DTC clears when the diagnostic runs and
does not fail at next ignition cycle.
• A history DTC clears with the Tech 2 or reset
switch operation.
Diagnostic Aids
• If an intermittent condition is suspected, refer to
Intermittent Conditions in this section.
DTC P0974 (Flash Code 71)
Schematic Reference: Transmission Controls
Schematics
Connector End View Reference: Transmission
Controls Connector End Views or Transmission Control
Module (TCM) Connector End Views
Step
Action
Value(s)
Yes
No
1
Did you perform the Diagnostic System Check -
Transmission Controls?
—
Go to Step 2
Go to Diagnostic
System Check -
Transmission
Controls
2
1. Install the Tech 2.
2. Turn OFF the ignition for 30 seconds.
3. Place the transmission in neutral and set the
parking brake.
4. Start the engine.
5. Operate the selector lever from N to D in order
to energize the 2-4-6-R shift solenoid valve.
6. Monitor the Diagnostic Trouble Code (DTC)
Information with the Tech 2.
Does the DTC fail this ignition?
—
Go to Step 3
Go to Diagnostic
Aids
3
1. Turn OFF the ignition for 30 seconds.
2. Disconnect the 2-4-6-R shift solenoid valve
harness connector.
3. Turn ON the ignition, with the engine OFF.
4. Monitor the DTC Information with the Tech 2.
Is DTC P0973 set?
—
Go to Step 5
Go to Step 4
Transmission Control System (Smoother) 7A-149
4
1. Test the control circuit between the
transmission control module (TCM) (pins 8
and 9 of B-425 connector) and the 2-4-6-R
shift solenoid (pin 2 of J-236 connector) for a
short to ground.
2. Repair the circuit(s) as necessary.
Did you find and correct the condition?
—
Go to Step 7
Go to Step 6
5
Important:
Replacement 2-4-6-R shift solenoid valve must be
learned.
Replace the 2-4-6-R shift solenoid valve. Refer to
Repair Instructions (Overhaul) - Gearshift Control
Box in this section.
Did you complete the replacement?
—
Go to Step 7
—
6
Important:
Replacement TCM must be programmed and
learned.
Replace the TCM. Refer to Transmission Control
Module (TCM) Replacement in this section.
Did you complete the replacement?
—
Go to Step 7
—
7
1. Reconnect all previously disconnected
harness connector(s).
2. Clear the DTCs with the Tech 2.
3. Turn OFF the ignition for 30 seconds.
4. Place the transmission in neutral and set the
parking brake.
5. Start the engine.
6. Operate the selector lever from N to D in order
to energize the 2-4-6-R shift solenoid valve.
7. Monitor the DTC Information with the Tech 2.
Did the DTC fail this ignition?
—
Go to Step 3
Go to Step 8
8
Observe the DTC Information with the Tech 2.
Are there any DTCs that you have not diagnosed?
—
Go to Diagnostic
Trouble Code (DTC)
List
System OK
Step
Action
Value(s)
Yes
No
7A-150 Transmission Control System (Smoother)
P0976 (Flash Code 73)
Circuit Description
The pulse width modulation (PWM) 1-3-5 shift solenoid
valve is located on the gearshift control box. The
transmission control module (TCM) controls the 1-3-5
shift solenoid valve by duty cycle signal based on
commanded gear position. The 1-3-5 shift solenoid is
commanded ON when the commanded gear is set to
1st, 3rd and 5th gear. When disengaging from 2nd, 4th,
6th and reverse gear, the 1-3-5 shift solenoid is also
commanded ON. The gear shift position sensor is used
to detect the shift side lever position feedback for the
shift solenoid valves movement. The TCM uses the gear
shift position sensor to determine the current gear
position with a combination of the gear select position
sensor. If the TCM detects a high voltage condition on
the 1-3-5 shift solenoid valve monitor circuit when the
solenoid valve is commanded OFF, this DTC will set.
Condition for Running the DTC
• DTC P0889 is not set.
• The ignition switch is ON.
• The ignition voltage is more than 20 volts.
• The emergency switch is OFF.
• The gearshift control box relay is commanded ON.
Condition for Setting the DTC
• The TCM detects a high voltage condition on the 1-
3-5 shift solenoid valve monitor circuit when the
solenoid valve is commanded OFF.
Action Taken When the DTC Sets
• The TCM illuminates the transmission warning
lamp when the diagnostic runs and fails.
• The TCM intermittently sounds buzzer when the
diagnostic runs and fails.
• The TCM commands OFF gearshift control box
relay.
• The TCM inhibits gearshift control and holds gear
position when the diagnostic runs and fails.
• The TCM inhibits gear select & shift position
learning and half-clutch learning.
Condition for Clearing the DTC
• The TCM turns OFF the transmission warning
lamp when the diagnostic runs and does not fail at
next ignition cycle
• The TCM stops the buzzer when the diagnostic
runs and does not fail at next ignition cycle.
• A current DTC clears when the diagnostic runs and
does not fail at next ignition cycle.
• A history DTC clears with the Tech 2 or reset
switch operation.
Diagnostic Aids
• If an intermittent condition is suspected, refer to
Intermittent Conditions in this section.
DTC P0976 (Flash Code 73)
Schematic Reference: Transmission Controls
Schematics
Connector End View Reference: Transmission
Controls Connector End Views or Transmission Control
Module (TCM) Connector End Views
Step
Action
Value(s)
Yes
No
1
Did you perform the Diagnostic System Check -
Transmission Controls?
—
Go to Step 2
Go to Diagnostic
System Check -
Transmission
Controls
2
1. Install the Tech 2.
2. Turn OFF the ignition for 30 seconds.
3. Turn ON the ignition, with the engine OFF.
4. Monitor the Diagnostic Trouble Code (DTC)
Information with the Tech 2.
Is DTC P0889 also set?
—
Go to DTC P0889
Go to Step 3
3
1. Turn OFF the ignition for 30 seconds.
2. Disconnect the 1-3-5 shift solenoid valve
harness connector.
3. Connect a DMM between the control circuit of
the 1-3-5 shift solenoid valve harness (pin 2 of
J-235 connector) and a known good ground.
4. Turn ON the ignition, with the engine OFF.
Is the DMM voltage more than the specified value
until this DTC fails?
18.0 volts
Go to Step 4
Go to Step 6
4
Is the DMM voltage more than the specified value
after this DTC fails?
18.0 volts
Go to Step 7
Go to Step 5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст