Isuzu N-Series. Service manual — part 65
1B-30 AIR CONDITIONING
Evaporator Core / Expansion Valve (LHD Model)
Legend
1. Evaporator assembly
7. Thermo sensor
2. Electronic thermostat
8. Lining
3. Upper case
9. Lower case
4. Insulator and under cover
10. Lining
5. Evaporator core
11. Insulator
6. Expansion valve
N1A0088E
AIR CONDITIONING 1B-31
Removal
Preparation:
Disconnect the battery ground cable.
Discharge and recover refrigerant.
1. Evaporator Assembly
Refer to “EVAPORATOR ASSEMBLY” removal
procedure in this section.
2. Electronic Thermostat
• Remove the sensor fixing clip.
• Pull out the grommet from the upper case to re-
move the thermostat.
3. Upper Case
• Separate the upper and lower case.
• Slit the case parting face with a knife since the lin-
ing is separated.
4. Insulator and Under Cover
5. Evaporator Core
Pull up the core from the lower case.
6. Expansion Valve
• Tear off the insulator (1) carefully.
• Remove the sensor fixing clip.
• Use a back up wrench when disconnecting all re-
frigerant pipes, and remove the expansion valve
(2).
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. O-rings cannot be reused. Always replace new
ones.
2. Be sure to apply new specified compressor oil to
the O-rings when connecting lines.
3. Be sure to install the expansion valve sensor and
the insulator on the place where it was before.
4. To install a new evaporator core, add 50cc (1.4
Imp. fl oz) of new specified compressor oil to a new
core and install the thermostat sensor to the evap-
orator core specified position with the clip where it
was before.
5. Tighten the refrigerant lines to the specified torque.
Tighten:
• Refrigerant line 1 to 10 N
⋅m (1.0 kg⋅m/7 lb⋅ft)
• Refrigerant line 2 to 15 N
⋅m (1.5 kg⋅m/11 lb⋅ft)
• Refrigerant line 3 to 20 N
⋅m (2.0 kg⋅m/14 lb⋅ft)
6. Apply an adhesive to parting face of lining when
assembling evaporator assembly.
7. The thermostat sensor (1) is installed on the core
with the clip (2) and it must not interfere with the
core.
N1A0089E
N1A0090E
N1A0091E
1B-32 AIR CONDITIONING
Evaporator Core / Expansion Valve (RHD Model)
Legend
1. Evaporator assembly
7. Evaporator core
2. Upper case
8. Pipe assembly
3. Lining
9. Lower case
4. Clip
10. Expansion valve
5. Amplifier & Thermistor
11. Insulator and cover
6. Thermo sensor
N1A0193E
AIR CONDITIONING 1B-33
Removal
Preparation:
Disconnect the battery ground cable.
Discharge and recover refrigerant.
1. Evaporator Assembly
Refer to “EVAPORATOR ASSEMBLY” removal
procedure in this section.
2. Amplifier & Thermistor
• Remove the sensor fixing clip.
• Pull out the grommet from the upper case to re-
move the thermostat.
3. Upper Case
• Separate the upper and lower case.
• Slit the case parting face with a knife since the lin-
ing is separated.
4. Insulator and Cover
5. Evaporator Core
Pull up the core from the lower case.
6. Expansion Valve
Take off two installation bolts and subsequently re-
move pipe assembly and expansion valve sequen-
tially.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Tighten the expansion valve to the specified
torque.
Tighten:
Installation bolts to 5 N
⋅m (0.5 kg⋅m/3.7 lb⋅ft)
2. O-rings cannot be reused. Always replace new
ones.
3. Be sure to apply new specified compressor oil to
the O-rings when connecting lines.
4. To install a new evaporator core, add 50cc (1.4
Imp. fl oz) of new specified compressor oil to a new
core.
5. Apply an adhesive to parting face of lining when
assembling evaporator assembly.
6. Install the amplifier & thermistor sensor (2) surely
to the evaporator core specified position with the
clip (1) where it was before.
N1A0194E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст