Isuzu N-Series. Service manual — part 1027
CAB AND CHASSIS ELECTRICAL 8-213
H-20
H-20
L-1
L-3
L-4
L-4
N-2
N-7
No.
Connector Face
002-009
1
2
002-010
1
2
002-027
2
1
002-027
2
1
002-022
1 2
002-023
2 1
001-009
1
001-009
1
P-1
(12 V)
P-2
P-1
(24 V)
P-4
P-2
(24 V)
P-3
P-5
(12 V)
P-5
(24 V)
No.
Connector Face
000-003
000-004
000-004
000-004
000-006
000-006
000-007
000-002
8-214 CAB AND CHASSIS ELECTRICAL
H-5
H-7
Starter Switch
Refer to “START AND CHARGING” in this section.
Key Cylinder Switch
Refer to “START AND CHARGING” in this section.
Backup Light Switch
Refer to “HORN, BACKUP LIGHT AND BACKUP
BUZZER” in this section.
Dome Light Bulb
Removal
Preparation:
Disconnect the battery ground cable.
1. Lens
Hold the lens and pull it downward.
2. Bulb
Installation
To install, follow the removal steps in the reverse order.
Dome Light Bulb (for Crew Cab)
Removal
Preparation:
Disconnect the battery ground cable.
1. Lens
Hold the lens and pull it down.
2. Bulb
Installation
To install, follow the removal steps in the reverse order.
Dome Light Switch
Inspection
Check the continuity between the dome light switch con-
nector terminals.
Repair or replace the switch when the result of inspec-
tion is found abnormal.
1
2
3
7
8
9
13
14 15
19
20 21
25
26 27
31
32 33
34
35
36
37
4
5
6
10
11 12
16
17 18
22
23 24
28
29 30
38
39 40
6
5
4
12
11 10
18
17 16
24
23 22
30
29 28
40
39 38
3
2
1
9
8
7
15
14 13
21
20 19
27
26 25
33
32 31
34
35
36
37
N8A5488E
1
2
1
2
1 2 3 4
5 6 7 8
9 10 11 12 13
14 15 16 17 18
2
1
2
1
4 3 2 1
8 7 6 5
13 12 11 10 9
18 17 16 15 14
H - 6
H - 7
H - 8
N8A5489E
N8A5243E
N8A0203E
CAB AND CHASSIS ELECTRICAL 8-215
Removal
Preparation:
Disconnect the battery ground cable.
1. Meter cluster
Refer to the “METER AND WARNING/INDICA-
TOR LIGHT” in this section.
2. Dome Light Switch
Release the lock pushing the switch from the back
side of the meter cluster.
Installation
To install, follow the removal steps in the reverse order
noting the following point.
1. Push the switch with your fingers until locks se-
curely.
Door Switch
Inspection
Check to see if there is any continuity between the ter-
minals and the body while operating the door switch.
Repair or replace the switch, when the result of inspec-
tion is found abnormal.
Removal
Preparation:
Disconnect the battery ground cable.
1. Door Switch
1) Remove the screw.
2) Disconnect the connector of the switch.
B-86
2
4
1
3
ON
OFF
Terminal
No.
SW
position
N8A0204E
N8A5160E
1
Body
Push
Release
Connector
No.
Terminal No.
SW
operation
N-2
N-7
N8A0206E
8-216 CAB AND CHASSIS ELECTRICAL
Installation
To install, follow the removal steps in the reverse order.
Key Remind Buzzer
The key remind buzzer sounds to remind the driver to remove the starter key from the starter switch when front driver
side door is opened (Front driver side door switch is on).
N8A0207E
Key cylinder SW
(Starter SW)
Key remind buzzer
F-16
(10A)
Front door SW
N8A0208E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст