Isuzu N-Series. Service manual — part 1019
CAB AND CHASSIS ELECTRICAL 8-181
6. Marker Light Inoperative
Lighting Switch
Refer to “HEADLIGHT, FOG LIGHT AND CORNERING
LIGHT” in this section.
Clearance Light/Bulb
Removal
1. Remove the battery ground cable at the battery.
2. Remove the front combination light.
• Open the cab door. Insert a screwdriver (1) into
the space between the cab and the cab door.
Use the screwdriver to force out the stud pin at
the center of the grommet (the pin securing the
front combination light).
• Remove the fixing screw.
• IS FUSE F-25 (15A) NORMAL?
• IS J-9 SECURELY GROUNDED?
YES
NO
REPLACE THE FUSE
• IS MARKER LIGHT RELAY NORMAL?
YES
NO
GROUND IT SECURELY
• IS THERE BATTERY VOLTAGE APPLIED TO THE
MARKER LIGHT CONNECTOR J-24 WHEN TURNING
THE LIGHTING SWITCH ON?
YES
NO
REPLACE THE MARKER LIGHT RELAY
• REPAIR A POOR CONNECTION AT THE CONNECTORS
OR AN OPEN CIRCUIT BETWEEN THE MARKER LIGHT
CONNECTORS J-25 - J-9
YES
NO
REPAIR A POOR CONNECTION AT THE
CONNECTORS OR AN OPEN CIRCUIT OF 2 X-22
OR BETWEEN 5 X-22 AND J-9
N8A0165E
Door side
Cab side
1
N8A5471E
8-182 CAB AND CHASSIS ELECTRICAL
• Remove the two catches.
• Remove the front combination light (1) connec-
tor.
3. Remove the clearance light bulb.
• Turn the bulb socket (3) to the left to remove it.
• Press the bulb (2) in and turn it to the left to re-
move it from the socket.
Installation
Installation procedure of cornering/clearance light bulb
1. Install the cornering/clearance light bulb.
• While pressing the bulb (2), turn it clockwise to
fit.
Notice:
Do not let the glass portion dirty with sebum etc.
• Turn the bulb socket (3) clockwise to fit.
2. Installation procedure of front combination light as-
sembly
• Connect the connector of the combination light
assembly.
• Position it by aligning two pawls with the groove
of H/L.
• Fit the iron PIN (1) in the upper portion of the
side by aligning it with the center of correspond-
ing grommet.
Notice:
Push it into securely with a force of approx. 250 N (25
kgf) until click is heard.
• Pull the front combination light assembly lightly
toward the front of vehicle to make sure that the
PIN and grommet are engaged securely.
• Tighten one bolt in the lower portion of front
combination light assembly.
3. Hook the seal rubber on two projections under H/L.
4. Connect the battery ground cable.
5. Check lighting of each light.
Taillight Bulb
Removal
1. Lens
2. Bulb
Installation
To install, follow the removal steps in the reverse order.
1
3
2
N8A5477E
1
3
2
N8A0445E
N8A0167E
CAB AND CHASSIS ELECTRICAL 8-183
License Plate Light Bulb
Removal
1. Cover
2. Lens
3. Bulb
Installation
To install, follow the removal steps in the reverse order.
Turn Signal Light, Hazard Warning Light,
and Stoplight
General Description
The circuit consists of the starter switch, turn signal light
(front and rear), turn signal light switch, hazard warning
light, flasher unit, stoplight and stoplight switch.
When turning on the respective switches with the starter
switch on, the turn signal light will operate. When the
turn signal light is flashing, the indicator light in the meter
also starts flashing. When the hazard warning switch is
turned on, the current flows to the flasher unit through
the hazard warning switch to cause the hazard warning
light to flash, independent of the position of the starter
switch. At the same time, the indicator lights in the meter
also start flashing.
The stoplight switch will turn on and the light comes on
once the brake pedal is depressed, independent of the
position of the starter switch.
N8A0168E
8-184 CAB AND CHASSIS ELECTRICAL
Parts Location
B-7
H5 - H7
H-22
SIDE
TURN
SIGNAL
LIGHT
(RH)
(FOR EC/TURKEY
N2
CATEGORY
W/CAB
ONLY)
H-20
SIDE TURN SIGNAL LIGHT (LH)
(FOR EC/TURKEY
N2 CATEGORY W/CAB ONLY)
SIDE TURN SIGNAL LIGHT (RH)
(FOR EC/TURKEY
N2 CATEGORY S/CAB ONLY)
J-62 TURN SIGNAL LIGHT (RH)
J-65 TURN SIGNAL LIGHT (LH)
R-1 STOPLIGHT (LH)
SIDE TURN SIGNAL LIGHT (LH)
(FOR EC/TURKEY N2 CATEGORY
S/CAB 12V ONLY)
SIDE TURN RELAY
(FOR EC/TURKEY N2 CATEGORY
S/CAB ONLY)
FUSE BOX ASM
F-4, F-5, F-11, F-19, F-20
B-16
FLASHER UNIT
B-53
TURN SIGNAL INDICATOR LIGHT (RH) (METER)
TURN SIGNAL INDICATOR LIGHT (LH) (METER)
J-9
N8A0536E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст