Isuzu N-Series. Service manual — part 520
Cooling System 6B-11
7. Remove the water pump assembly while inserting
and scraping with the driver at the position shown
in the figure.
Legend
1. Water Pump
2. Water Pump Pulley
3. Setting Plate
Inspection
1. External check
• Check for cracks or damage in the pump body.
• Check for cracks and corrosion in the impeller.
• Check for water leakage from the seal unit.
• If you find abnormalities, replace with the water
pump assembly.
2. Bearing nut check
• Rotate the fan center while pushing it along the
radial direction. Confirm that there is no
abnormal noise and no excessive play.
• If you find abnormalities, replace with the water
pump assembly.
Installation
1. Mount the water pump assembly.
• Coat the fluid gasket (ThreeBond 1207C or
equivalent) to a bead diameter 3 to 5 mm (0.12
to 0.20 in) in the groove of the mounting surface
of the water pump.
• Mount the water pump to match with the studs
of the front cover within 7 minutes after coating
the fluid gasket.
• Refer to the figure for the offset in position of
the fluid gasket.
Tighten:
Bolts and nuts to 24 N
⋅m (2.4 kg⋅m/17 lb⋅ft)
N6A6340E
N6A6341E
N6A6342E
N6A6343E
6B-12 Cooling System
2. Temporarily fit the bolts until the water pump pulley
and the setting plate are properly seated in the
water pump assembly.
Legend
1. Fan Pulley
2. Setting Plate
3. Mount the fan belt, tighten the adjusting bolts of
the generator, and adjust the tension.
• Refer to “Drive Belt” in Section 6B.
4. After fan belt adjustments, tighten the generator
using the specified torque.
Tighten:
Nut and bolt to 2 members: 24 N
⋅m (2.4 kg⋅m / 17 lb⋅ft)
Nut and bolt to 3 members: 40 N
⋅m (4.1 kg⋅m / 30 lb⋅ft)
Legend
1. Adjusting Bolt (With A/C)
2. Lock Nut
3. Bolt
5. After the fan belt adjustments, tighten the
temporarily fitted fan pulley and setting plate using
the specified torque.
Tighten:
Bolt to 24 N
⋅m (2.4 kg⋅m / 17 lb⋅ft)
6. Tighten the fan assembly using the specified
torque for mounting.
Tighten:
Nut to 24 N
⋅m (2.4 kg⋅m / 17 lb⋅ft)
Legend
1. Fan Assembly
2. Nut
3. Setting Plate
4. Fan Pulley
5. Bolt
7. Mount the fan guide.
8. Mount the radiator lower hose.
9. Fill the cooling water.
N6A6344E
N6A6339E
N6A6338E
Cooling System 6B-13
Torque Specifications
N6A6345E
6B-14 Cooling System
Thermostat
Components
Legend
1. Radiator Upper Hose
2. Water Outlet Pipe
3. Thermostat
4. Gasket
Removal
1. Drain the cooling water. Prepare the container for
discharging and use it for replenishment when
mounting the thermostat. Set the discharge of
cooling water such that the water does not flow out
of the thermostat housing.
2. Remove the radiator upper hose from the radiator
side.
3. Remove the water outlet pipe.
4. Remove the thermostat.
5. Remove the gasket from the thermostat.
Inspection
• Place the thermostat in water and increase the
temperature while stirring it sufficiently.
• Measure the temperature when the valve is just
opened and when it is fully open.
N6A6346E
N6A6347E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст