Isuzu N-Series. Service manual — part 536
Engine Electrical 6D-11
Legend
1. Nut
2. Pulley
3. Fan
4. Spacer
5. Front Cover
6. Front Ball Bearing
7. Bearing Retainer
8. Rotor and Rear Bearing
9. Diode Brush Regulator Assembly
10. Stator
11. Rear Cover
12. Through Bolt
13. Housing
14. Vane
15. Pump Rotor
16. Side Plate
17. Vacuum Pump Assembly
Important:
• Separate the stator and rear cover. Be sure you
identify the proper position of the insulated
washers to prevent improper installation.
Inspection
• All metal parts except the voltage rectifier bridge,
stator, rotor and bearing assemblies in a suitable
solvent.
• Wipe or blow the components dry.
• Brush holder and brushes. The brushes have a
line that indicates their limit. If the brushes are
shorter than 6.5 mm (0.256 in) replace the
brushes.
1
9
11
12
13
14 15
16
2
3
4
5
6
7
8
10
17
N6A6594E
6D-12 Engine Electrical
Legend
1. Brush Holder
2. Brushes
• Voltage regulator for damage or corrosion.
• Bearings and spacer. Rotate the bearing and
check for roughness or excessive drag. If in doubt
about the bearing, replace it.
• Rotor and stator windings for burned insulation or
broken terminal connectors, wires, etc.
Burned insulation may appear as very dark or
blackened wiring, and sometimes charred paint or
a combination of the two. Replace the rotor or
stator if the windings are burned.
• Generator frames. Check for distortion, cracks or
damage. Replace as necessary.
• Rotor slip rings. If the rings are dirty, clean them
with 500–600 grain or finer polishing cloth.
Clean the slip rings with rubbing alcohol if the rings
are contaminated. Spin the rotor and hold the
polishing cloth against the rings until they are
clean. Slip rings which are rough, scored, or out-of-
round, must be machined in a lathe to 31.7 mm
(1.248 in). Finish the slip rings with 500 – 600 grain
or finer polishing cloth and blow away all dust
particles after the machining process.
• All vacuum pump components for wear, damage or
other abnormal conditions.
• Check valve.
1) Carefully force the valve from the “B” side as
shown in the illustration.
The valve must move smoothly.
If it does not, the check valve must be replaced.
2) Apply compressed air to the “A” side.
Check for air leakage from the check valve.
If there is air leakage, the valve must be replaced.
2
1
N6A6595E
Air Pressure
kPa (kg/cm
2
/ psi)
98 – 490 (1 – 5/14 – 71)
slip rings
N6A6596E
Air
Pressure
A
B
N6A6597E
Engine Electrical 6D-13
• Oil seal (O-ring). Check the inner face of the rear
cover for traces of oil leakage. Be sure the inner
face of the oil seal is not worn or damaged.
If worn or damaged, use a screwdriver to remove
the oil seal (O-ring) from the rear cover.
Install a new oil seal (O-ring) using an oil seal
installer or equivalent.
Measure
Replace the housing if not within these specifications.
Electrical Bench Tests (Generator)
1. Measure the rotor coil resistance.
2. Check for continuity between the slip rings and the
rotor core or shaft.
If there is continuity, the entire rotor assembly must
be replaced.
The length of the vanes
mm (in)
17.0 – 18.0 (0.669 – 0.709)
The inside diameter of the vacuum pump
housing
mm (in)
69.5 – 69.6 (2.736 – 2.740)
N6A6407E
N6A6598E
Rotor Coil Resistance at 20
°C (68°F)
ohms
Standard
50A
7.6
60A
9.2
80A
10.2
N6A6599E
slip rings
N6A6600E
6D-14 Engine Electrical
Stator Coil Assembly
1. Check for continuity across the stator coils
If there is no continuity, the stator coils must be
replaced.
2. Check for continuity between each stator coil end
and the stator core.
If there is continuity, the stator coils must be
replaced.
Rectifier
Resistance Between Stator coil neutral
point and the Coil Ends (Reference)
mm (in)
Standard
50A
0.195
60A
0.137
80A
0.073
stator coil
neutral point
stator coil end
N6A6601E
stator coil end
stator core
N6A6602E
N6A6603E
Tester wire
E
+
−
BAT
+
−
U, V, and WN
U, V, and WN
+
-----
Conductivity
+
-----
No conductivity
−
No conductivity
-----
−
Conductivity
-----
Negative side diode check
Positive side diode check
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст