Isuzu N-Series. Service manual — part 1040
CAB AND CHASSIS ELECTRICAL 8-265
Remove two retaining nuts from right hand side of
pivot.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
• Temporarily fit the wiper motor by using one of the
four wiper motor fixing screws.
• Put the crank arm ball joint in the wiper link hole
and fix them together while pulling the wiper link.
• Fit the motor with four screws.
• Tighten the pivot nut with the specified torque.
Tighten:
Pivot nut to 8 N
⋅m (80 kg⋅cm/70 lb⋅in)
• Tighten the wiper arm nut with the specified torque.
Tighten:
Wiper arm nut to 17 N
⋅m (170 kg⋅cm/147 lb⋅in)
Wiper Blade Rubber
Removal
1. Wiper Blade
Push the wiper blade lock while pulling the wiper
blade in the arrow direction.
Notice:
When the wiper blade has been removed, wrap the tip
of the wiper arm with cloth, to avoid damaging the glass.
2. Wiper Blade Rubber
1) Pull the end of rubber and remove the projec-
tion from the click of the blade stay.
2) Pull the rubber out in the same direction.
6
Pivot (Wiper: RH)
N8A0278E
N8A0477E
N8A0280E
8-266 CAB AND CHASSIS ELECTRICAL
Installation
1. Wiper Blade Rubber
Install the click of the blade stay in the groove of the
new rubber and slide it in. Complete installation by
pushing the click.
Finally, check that the click of the stay has caught
in the hole of the rubber.
2. Wiper Blade
Push the lock of wiper blade (1) into the retentive
portion on the tip of wiper arm (2).
Audio and Cigar Lighter
General Description
The circuit consists of the starter switch, radio, cigar
lighter and the relay.
The audio circuit is designed for the current to flow
through the receiver circuit when the radio switch is
turned on with the starter switch in “ACC” or “ON”. Cur-
rent runs through the memory circuit of the audio regard-
less of the position of the starter switch.
When the cigar lighter is pushed in with the starter
switch at either “ACC” or “ON” position, a circuit is
formed in the cigar lighter case to heat the lighter coil.
The cigar lighter is spring back to its original position af-
ter the lighter coil is heated.
N8A0281E
N8A0282E
1
2
N8A0486E
CAB AND CHASSIS ELECTRICAL 8-267
Parts Location
X-4 TAIL RELAY
F-4, F-7, F-15
N8A0283E
8-268 CAB AND CHASSIS ELECTRICAL
Circuit Diagram
2
D-5
1
D-5
H-7
1
5
10
11
4
6
13
5
12
9
6
7
6
7
1
2
1
B-28
B-28
B-28
B-28
B-67
B-45
H-11
H-2
H-2
B-28
B-28
B-28
B-28
4
H-11
B-44
B-43
2
2
1
2
B-7
X-4
X-4
X-4
X-4
H-6
B-67
B
ST
ACC
ON
OFF
STARTER SWITCH
FL-1 100A or 120A
KEY SW
FL-2 40A(24V)
50A(12V)
AUDIO(B),
DOOR LOCK
F-4 15A
F-15 15A
1
RELAY; TAIL
LIGHTING SWITCH(8)
(COMBINAITION SWITCH)
(24V MODEL)
HEADLIGHT BRACKET (LH)
CLEARANCE LIGHT (LH)
3W/B
5W
3W/B
3W/B
0.85LG/R
3W
0.3G/O
0.5B
3B
2B
5W/B (24V)
8W/B (12V)
3R/Y
0.5R/Y
0.5R
2B
0.3B
0.5G/R
0.5G/R
0.5G
0.5G
0.5O
0.5O
0.5B
0.5B
0.5LG/R
SPEAKER (LH)
SPEAKER (RH)
RADIO & CLOCK
CIGAR LIGHTER
P-1
P-2
P-3
P-4
P-5
MAIN
3W/L
5W
AUDIO(IG)
CIGAR LIGHTER
1
B-43
2
D-1
1
D-1
0.5LG/R
FRAME
(12V)
8W
0.85LG/R
0.5B (24V)
1.25B (12V)
2L
0.5R/Y
0.5R/Y
TAIL
LIGHT
F-7 10A
0.85G/B
N8A0284E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст