Isuzu N-Series. Service manual — part 639
6E-4 EXHAUST GAS RECIRCULATION (EGR) SYSTEM
EGR SYSTEM WIRING DIAGRAM
For 4JB1-TC/4JG2
1. Connector Pin Assignment
N6A3580E
No.
Connector Name
1
—
2
Battery (
−) c/u GND
3
Thermo Switch
4
Battery (+)
5
—
6
—
7
rpm Signal (+)
8
rpm Signal (
−)
9
Potentiometer (+)
10
Potentiometer
11
Potentiometer (
−)
12
—
13
VSV
N6A3581E
EXHAUST GAS RECIRCULATION (EGR) SYSTEM 6E-5
EGR SYSTEM OPERATION
1. On the input side of engine speed, there is provided a hysteresis of 50 rpm on the speed rising side.
2. It does not work until 70 seconds, pass after engine start.
3. It does not work while the water temperature switch is on (30
°C or lower).
4. While engine speed drops from 3,800 rpm or higher, it does not work for 25 seconds.
Exhaust Gas Recirculation (EGR) System Check
Step
Action
Value
YES
NO
1
Check the EGR valve for looseness.
Is the EGR valve loose?
—
2
Tighten the EGR valve.
Is the action complete?
—
Verify repair
—
3
1. Engine “OFF”.
2. Ignition “ON”.
3. Using test light to ground, check the EGR
harness between the EGR valve and igni-
tion feed.
Does the test light illuminate?
—
4
Repair the EGR harness ignition feed.
Was the problem corrected?
—
Verify repair
5
1. Remove the EGR valve.
2. Visually and physically inspect the EGR
valve pintle, valve passages and adapter
for excessive deposits, obstructions or
any restrictions.
Does the EGR valve have excessive deposits,
obstructions or any restrictions?
—
6
Clean or replace EGR system components as
necessary.
Was the problem corrected?
—
Verify repair
7
1. Remove the EGR inlet and outlet pipes
from the intake and exhaust manifolds.
2. Visually and physically inspect manifold
EGR ports and EGR inlet and outlet pipes
for blockage or restriction caused by ex-
cessive deposits or other damage.
Do the manifold EGR ports or inlet and outlet
pipes have excessive deposits, obstructions,
or any restrictions?
—
EGR system work-
ing properly. No
problem found.
8
Clean or replace EGR system components as
necessary.
Is the action complete?
—
Verify repair
—
6E-6 EXHAUST GAS RECIRCULATION (EGR) SYSTEM
INSPECTION
Vacuum Switch Valve (VSV)
Check the resistance between the VSV connector termi-
nals using a circuit tester.
Cold Resistance: 37 — 44 (
Ω) (for 12 volt)
Connect battery voltage between VSV connector termi-
nals and make sure of the continuity between the ports.
EGR Valve
With negative pressure applied to the diaphragm cham-
ber, make sure that the valve is smoothly actuated to
make the area between (1) and (2) ventilated.
Startup: About — 18.66
±2.67 Kpa (−140±20 mmHg)
Check to see if EGR valve is normally actuated under
the following conditions:
QWS off (After warming up)
Engine coolant temp: 80
°C or higher
Legend
1. 2 pin
2. Port
N6A3583E
N6A3584E
Illustration
Tool Number /
Description / Remarks
5-8840-0366-0 / High
Impedance Multimeter
(Digital Voltmeter-DVM)
5-8840-0279-0 / Vac-
uum Pump with Gauge
5884003660
5884002790
EXHAUST GAS RECIRCULATION (EGR) SYSTEM 6E-7
EGR COOLER
Component
Removal
Preparation
• Disconnect the battery ground cable.
• Drain the coolant.
• Remove the water hose.
1. EGR Cooler Bracket
Remove the bracket from the flywheel housing.
2. EGR Cooler
Remove the EGR fixing nuts. Remove the cooler
together with the gasket.
3. EGR Pipe
4. EGR Valve
Legend
1. EGR cooler bracket
3. EGR pipe
2. EGR cooler
4. EGR valve
N6A3585E
N6A3586E
Legend
1. EGR cooler
2. EGR cooler bracket
Legend
1. EGR valve
2. EGR pipe
N6A3587E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст