Isuzu N-Series. Service manual — part 612
6C-18 ENGINE FUEL
Caution:
• The spray condition, when judged with a nozzle
tester, is deemed as normal so long as the spray
form is not excessively deformed.
Oil Tight Test (4JG2 Engine)
1. After completion of the adjustment of injection
pressure, wipe off light oil at the tip of the nozzle
with waste.
2. With pressure 1,961 Kpa (20 kg/cm
2
/284 psi) less
than the specified injection pressure applied,
check to see if an oil drop trickles off the tip of the
nozzle within 10 seconds after application of pres-
sure. (There is no problem with the nozzle when oil
gathers at the tip, but does not drop off.)
3. When an oil drop trickles, clean the nozzle thor-
oughly.
Then reassemble it to check for any dropping of oil.
When oil still drops, change it with a new one.
Installation (4JG2 Engine)
Caution:
• Nozzle and assembling should be as illustrated.
• Use new heat shield and new corrugated washer.
1. Injection Nozzle (4JG2 only)
• Lightly tighten the holder nut to suck extent that the
nozzle holder can turn one word and one word.
• Set positioning confirmation drilled hole (
φ2) within
a nozzle turning angle of
±5° against the cylinder
headside positioning boss.
N6A3747E
N6A3748E
Legend
1. Cylinder head side
2. Nozzle heat shield
3. Gasket heat shield
4. Nozzle
N6A3749E
N6A3072E
ENGINE FUEL 6C-19
• Apply a wrench as illustrated and tighten the holder
nut to the specified torque using a special tool.
Caution:
• After tightening the holder nut, make sure that the
drilled hole makes
±5° or smaller with the cylinder
head-side positioning boss.
• When mounting leak off pipe, injection nozzle and
pipe, clean with air so that dust may not enter.
Tighten:
Nozzle Fixing Nut to 64 N
⋅m (6.5 kg⋅m/47 lb⋅ft)
Wrench: nozzle holder 5-8840-0259-0
2. Leak Off Pipe
• Mount using a new copper washer.
• Tighten nut to the specified torque.
Tighten:
Pipe Nut to 29 N
⋅m (3.0 kg⋅m/22 lb⋅ft)
3. Injection Pipe
• Connect injection pipe to nozzle holder.
• Tighten the injection pump side.
Tighten:
Sleeve Nut to 29 N
⋅m (3.0 kg⋅m/22 lb⋅ft)
• Fit pipe clip in specified position.
4-1 Injection Nozzle (Two Spring Nozzle Holder)
(4JB1-TC)
The two-spring nozzle holder has been developed to re-
duce NOx (Nitrogen Oxides) and particulates from direct
injection diesel engine exhaust.
Disassembly
1. Retaining nut (1)
2. Nozzle & pin (2)
3. Spacer & pin (3)
4. Lift piece (4)
5. Spring seat (5)
6. Push rod (6)
7. Shim (Second nozzle opening pressure adjust-
ment) (7)
8. Second spring (8)
9. Collar (9)
10. Spring seat (10)
11. First spring (11)
12. Shim (First nozzle opening pressure adjustment)
(12)
13. Nozzle holder body (13)
14. Eye bolt (14)
15. Gasket (15)
1) Before disassembly, remove carbon deposit
from nozzle and nozzle holder using a wire
brush and wash the outside nozzle holder as-
sembly.
Caution:
Do not touch nozzle holes with the wire brush during
cleaning it.
2) Disassemble the nozzle holder assembly to nu-
merical order.
Legend
1. Glow plug
2. Positioning boss
N6A3751E
N6A3402E
6C-20 ENGINE FUEL
Reassembly and Opening Pressure Adjust-
ment (4JB1-TC)
1. Nozzle holder body
2. Shim (First opening pressure adjustment)
3. First spring
4. Spring seat
5. Collar
6. Second spring
7. Push rod
8. Shim (Second opening pressure adjustment)
9. Spring seat
10. Lift piece
11. Spacer & pin
12. Nozzle & pin
13. Retaining nut
14. Gasket
15. Eye bolt
The nozzle holder is adjusted as the components are re-
assembled in the sequence above.
As adjustment of the two-spring nozzle holder is made
in hundredths of a millimeter, clean the parts thoroughly
in light oil to completely remove any dirt or foreign mat-
ter.
N6A3403E
ENGINE FUEL 6C-21
Reassembly and Adjustment Procedure
First Nozzle Opening Pressure Adjustment
1. Claim the nozzle holder in a vise.
2. Install the shim, first spring and spring seat in the
nozzle holder.
3. Install the collar, second spring, shim, spring seat
and push rod in the nozzle holder.
N6A3692E
Legend
1. Nozzle holder body
N6A3404E
Legend
1. Spring seat
2. First spring
3. First nozzle opening pressure adjusting shim
N6A3405E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст