Isuzu N-Series. Service manual — part 602
6A1-96 4JB1/4JB1-TC/4JG2/4JH1-TC - ENGINE
10. Power Steering Pump & Bracket Assembly (Power
Steering Model)
1) Loosen the idler pulley lock nut.
2) Loosen the adjust bolt then remove the drive
belt.
3) Remove the pipe bracket fixing bolt and clip.
4) Remove the power steering pump fixing bolts
pump to chassis frame side use the wire.
11. Actuator Vacuum Hose (Exhaust Brake Model)
• Disconnect the vacuum hose from actuator side.
12. Vacuum Pump Hose (Exhaust Brake Model)
• Disconnect the vacuum hose from vacuum tank
side and magnetic valve side.
13. Front Exhaust Pipe
• Remove the exhaust pipe fixing bolts from exhaust
manifold.
• Remove the exhaust pipe stay bolt.
• Remover the fixing nuts from front pipe.
Legend
1. Bracket
2. Clip
3. Lock nut
N6A3290E
N6A3362E
N6A3363E
N6A3364E
4JB1/4JB1-TC/4JG2/4JH1-TC - ENGINE 6A1-97
14. Support Rubber
1) Right Hand
• Remove two fixing nuts at the cross member
side.
2) Left Hand
• Remove two fixing nuts at the cross member
side.
15. Engine Assembly
1) Lift engine carefully by using hoist.
2) Lift front part of engine higher than rear part of
it.
3) Take out engine assembly taking care not to
damage full pipes, brake pipes and so on.
Installation
1. Engine Assembly
• Position engine mountings by using hoist.
2. Support Rubber
• After all fixing bolts (left: two bolts, right: two bolts)
were inserted to every holes, and engine asm and
tighten fixing bolts to the specified torque.
Tighten:
• 40 N
⋅m (4.1 kg⋅m / 30 lb⋅ft)
3. Front Exhaust Pipe
• Connect the exhaust pipe and tighten nut to the
specified torque.
Tighten:
• Exhaust pipe nut to 69 N
⋅m (7.0 kg⋅m / 51 lb⋅ft)
N6A3294E
N6A3300E
N6A3367E
N6A3300E
6A1-98 4JB1/4JB1-TC/4JG2/4JH1-TC - ENGINE
• Install the exhaust pipe stay and tighten bolt nut to
the specified torque.
Tighten:
• Stay bolt nut to 40 N
⋅m (4.1 kg⋅m / 30 lb⋅ft)
4. Vacuum Pump Hose (Exhaust Brake Model)
• Connect the vacuum hose to vacuum tank side and
magnetic valve side.
5. Actuator Vacuum Hose (Exhaust Brake Model)
• Connect the vacuum hose to actuator.
6. Power Steering Pump & Bracket Assembly (Power
Steering Model)
• Install the power steering pump and pipe bracket
then tighten bolts to the specified torque.
Tighten:
• Pump bolts to 19 N
⋅m (1.9 kg⋅m / 14 lb⋅ft)
• Pipe bracket bolts to 19 N
⋅m (1.9 kg⋅m / 14 lb⋅ft)
• Clip bolt to 10 N
⋅m (1.0 kg⋅m / 87 lb⋅in)
• Install Power Steering pump drive belt (1) and ad-
just belt tension.
Check drive belts for wear or damage, and replace
with new ones as necessary.
Check belts for tension, and adjust as necessary.
N6A3294E
N6A3364E
Legend
1. Bracket
2. Clip
3. Lock nut
N6A3363E
N6A3362E
4JB1/4JB1-TC/4JG2/4JH1-TC - ENGINE 6A1-99
• Push the middle of belts with a force of 10 kg and
check each bolt for deflection.
• Standard deflection
4JG2
• P/S pump lock bolt loose, adjust belt tension with
adjust belt.
Tighten:
• Idler lock nut to 27 N
⋅m (2.8 kg⋅m / 20 lb⋅ft)
4JB1
7. A/C Compressor Assembly (A/C Model)
• Install the A/C compressor fixing bolts and tighten
bolts to the specified torque.
Tighten:
• Compressor fixing bolts to 37 N
⋅m (3.8 kg⋅m / 27 lb⋅ft)
• Connect the magnetic clutch harness connector.
• Install A/C compressor drive belt (1) and adjust belt
tension.
Check drive belts for wear or damage, and replace
with new ones as necessary. Check belts for ten-
sion, and adjust as necessary.
• Push the middle of belts with a force of 10kg and
check each bolt for deflection.
• Standard deflection
4JG2
mm (in)
Initial tension
P/S pump drive belt
8 — 12 (0.31 — 0.47)
Legend
1. A/C compressor drive belt & P/S pump drive
belt
2. AC generator & fan pulley drive belt
N6A3427E
N6A3295E
mm (in)
Initial tension
A/C compressor drive belt
8 — 12 (0.31 — 0.47)
N6A3290E
N6A3428E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст