Isuzu N-Series. Service manual — part 574
GENERAL ENGINE MECHANICAL 6A-53
3. Measure the oil clearance between the connecting
rod and the crankshaft by:
1) Remove the connecting rod cap nuts and the
rod caps.
Arrange the removed rod caps in the cylinder
number order.
2) Clean the rod bearings and the crankshaft pins.
3) Carefully check the rod bearings.
If even one bearing is found to be damaged or
badly worn, the entire bearing assembly must
be replaced as a set. Reinstall the bearings in
their original positions.
Apply plastigage to the crank pin.
4) Put the plastigage, and reinstall the rod caps to
their original positions.
5) Tighten the cap nuts in 2 steps, using angular
tightening method as shown in the following
specifications. (4JG2, 4JH1-TC, 4JB1-TC)
Tighten:
• 4JH1-TC, 4JB1-TC to
1st Step: 29 N
⋅m (3 kg⋅m/22 lb⋅ft)
2nd Step: 45
° — 60°
• 4JB1 to 83 N
⋅m (8.5 kg⋅m/61 lb⋅ft)
Notice:
Do not allow the crankshaft to rotate.
6) Remove the rod caps.
7) Measure the width of the plastigage and deter-
mine the oil clearance. If the oil clearance ex-
ceeds the limit, replace the rod bearings as a
set.
8) Remove the plastigage from the bearings and
the crankshaft pins.
Reassembly
1. Connecting Rod
2. Piston
3. Piston Pin
Apply a cost of engine oil to the piston pin and the
piston pin hole.
N6A3184E
N6A3185E
Crankshaft Journal and Bearing Clearance
mm (in)
Standard
Limit
4JB1 /
4JB1-TC
0.029 — 0.066
(0.0011 — 0.0026)
0.100 (0.0039)
4JG2
4JH1-TC
0.029 — 0.083
(0.0011 — 0.0033
N6A3186E
6A-54 GENERAL ENGINE MECHANICAL
4. Piston Pin Snap Ring
Apply a thin coat of engine oil to the piston pin.
Try to insert the piston pin into the piston pin hole
with normal finger pressure.
Weigh each piston and connecting rod assembly.
Select piston and connecting rod combinations so
that the weight variation of the different assemblies
a held within the specified limits.
Notice:
When changing piston/connecting rod combinations, do
not change the piston/piston pin combination
• Attach the piston to the connecting rod with the
piston front mark and the connecting rod ISU-
ZU mark on the same side.
5. Piston Ring
• Install the piston rings with the piston ring ex-
pander.
The compression ring must be set with the N
mark facing up.
• Discrimination mark is painted as shown in the
illustration.
• Install piston rings in the following sequence.
1) Oil ring
4JB1, 4JH1-TC
2) 2nd compression ring
3) 1st compression ring
• The compression ring must be set with the
1N or 2N mark (4JG2) facing up.
• 1st compression ring: 1N (4JG2), N (4JB1),
R (4JH1-TC)
g (oz)
Variance in weight after
assembly
Less than 3 (0.1058)
Legend
1. Front mark
2. ISUZU mark
N6A3187E
Legend
1. N mark (Top ring) (2nd ring) (4JB1)
2. 1N mark (Top ring) 2N mark (2nd ring) (4JG2)
3. R mark (Top ring) (2nd ring) (4JH-TC)
Legend
1. Expander ring
2. Upper side rail
3. Lower side rail
N6A3178E
N6A3188E
GENERAL ENGINE MECHANICAL 6A-55
• 2nd compression ring: 2N (4JG2), N (4JB1),
R (4JH1-TC)
• After installation, apply engine oil to the en-
tire circumference of the piston rings.
Check to see that all the rings rotate smooth-
ly.
• Insert the bearings into the connecting rods
and caps.
Apply new engine oil to the bearing faces.
Cap side bearings have no oil hole.
Connecting rod side bearings oil hole should
be aligned with oil hole on the connecting
rod.
4JG2
6. Piston and Connecting Rod
• Apply engine oil to the cylinder bores, the con-
necting rod bearings and the crankshaft pins.
• Check to see that the piston ring end gaps are
correctly positioned.
• Insert the piston/connecting rod assemblies
into each cylinder with the piston ring compres-
sor.
• The front marks must be facing the front of the
engine.
7. Connecting Rod Bearing Cap
• Tighten the cap nuts in 2 steps, using angular
tightening method as shown in the following
specifications.
Tighten:
4JH1-TC, 4JB1-TC to
• 1st Step: 29 N
⋅m (3.0 kg⋅m/22 lb⋅ft)
• 2nd Step: 45
° — 60°
4JB1 to 83 N
⋅m (8.5 kg⋅m/61 lb⋅ft)
After tightening the cap nuts, check to see that the
crankshaft rotates smoothly.
8. Piston Cooling Oil Pipe
• Install the piston cooling oil pipe to the cylinder
body.
• Tighten the oil pipe bolts and relief valve to the
specified torque.
Tighten:
Oil Pipe Bolt to
• M8
× 1.25: 19 N⋅m (1.9 kg⋅m/14 lb⋅ft)
• M6
× 1.00: 8 N⋅m (0.8 kg⋅m/69 lb⋅in)
Oil Pressure Regulating Valve to
• M16
× 1.5: 29 N⋅m (3.0 kg⋅m/22 lb⋅ft)
Legend
1. Oil ring
2. Compression ring No. 2
3. Compression ring No. 1
N6A3189E
Legend
1. Expander ring
2. Expander ring
3. Upper side rail
4. Lower side rail
N6A3190E
6A-56 GENERAL ENGINE MECHANICAL
Notice:
Check that there is no interference between the piston
and the oiling jet pipe by slowly rotating the crankshaft.
9. Oil Pump Assembly
10. Oil Pan Assembly
Above works refer to “OIL PUMP” Section in this
manual.
11. Cylinder Head Assembly
• Piston Head Projection Measurement Point
• Cylinder Head Assembly
• Push Rod
• Rocker Arm Shaft Assembly
Valve clearance adjustment.
Above works refer to “CYLINDER BLOCK” Section
in this manual.
N6A3191E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст