Isuzu N-Series. Service manual — part 330
6A-62 ENGINE MECHANICAL
4. Piston Pin
If could not be installed piston pin, it is recommend-
ed to remove it by following procedure.
1) Use a piston heater to heat the piston to 80 —
100
°C (176 — 212°F).
2) Apply a coat of the engine oil to the piston pin.
3) Use your fingers to force the piston pin into the
piston until it makes contact with the snap ring.
4) Check to see if the connecting rod moves
smoothly on the piston pin.
5. Snap Ring
6. Piston Ring
1) Use a piston ring replacer to install the three
piston rings.
Install the piston rings in the order shown in the il-
lustration.
Notice:
Insert the expander coil into the oil ring groove so that
there is no gap on either side of the expander coil before
installing the oil ring.
Install the compression rings with the stamped side fac-
ing up.
2) Apply engine oil to the piston ring surfaces.
N6A0272E
N6A0273E
Legend
1. 1st compression ring
2. 2nd compression ring
4. Oil ring
Legend
A. For 4HE1-TC
1. 1st compression ring
2. 2nd compression ring
3. 3rd compression ring (For 4HE1-TC)
4. Oil ring
N6A0274E
N6A0275E
ENGINE MECHANICAL 6A-63
3) Check to see if the piston rings rotate smoothly
in the piston ring grooves.
7. Connecting Rod Bearing
Carefully wipe any oil or other foreign material from
the connecting rod bearing back face and the con-
necting rod bearing fitting surface.
8. Piston and Connecting Rod Assembly
Notice:
When installing new connecting rod and/or connecting
rod bearings, refer to the selection table. Above works
refer to “CRANKSHAFT” section in this manual.
1) Apply a coat of the engine oil to the circumfer-
ence of each piston ring and piston.
2) Position the piston ring gaps as shown in the il-
lustration.
3) Apply a coat of molybdenum disulfide grease to
the two piston skirts.
This will facilitate smooth break-in when the en-
gine is first started after reassembly.
4) Apply a coat of the engine oil to the upper bear-
ing surfaces.
5) Apply a coat of the engine oil to the cylinder
wall.
6) Position the piston head front mark so that it is
facing the front of the engine.
7) Use the piston ring compressor to compress
the piston rings.
Piston Ring Compressor: 5-8840-9018-0
8) Use a hammer grip to push the piston in until
the connecting rod makes contact with the
crankpin.
At the same time, rotate the crankshaft until the
crankpin is at bottom dead center.
Caution:
Do not bend or damage the oiling jet.
9. Connecting Rod Cap
1) Install the connecting rod bearing caps.
2) Align the bearing cap cylinder number marks
(1) and the connecting rod cylinder number
marks (1).
3) Apply a coat of molybdenum disulfide grease to
the threads and setting faces of each connect-
ing rod cap bolts.
N6A0276E
N6A0277E
Legend
A. Front mark
1. 1st compression ring
2. 2nd compression ring
3. 3rd compression ring (For 4HE1-TC only)
4. Oil ring
5. Coil expander
N6A0278E
6A-64 ENGINE MECHANICAL
4) Tighten the connecting rod caps to the speci-
fied torque.
Tighten:
Connecting rod bearing cap bolt to
• 1st step: 39 N
⋅m (4.0 kg⋅m / 29 lb⋅ft)
• 2nd step: 60
°
• 3rd step: 30
°
Angle gauge: 5-8840-0266-0
10. Oil Pump Strainer
11. Oil Pan
12. Spacer Rubber
13. Cylinder Head Gasket
Above works refer to “CYLINDER BLOCK” section
in this manual.
14. Cylinder Head Assembly
Above works refer to “CYLINDER HEAD” section
in this manual.
Legend
1. Alignment
2. Boss discriminating the front from the rear
N6A0279E
N6A0280E
ENGINE MECHANICAL 6A-65
CYLINDER BLOCK
Component
N6A1624E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст