Isuzu N-Series. Service manual — part 729
6E-338 Engine Control System (4HK1)
Installation Procedure
1. Install the ECT sensor (1).
2. Connect the ECT sensor connector.
3. Replenish any lost engine coolant.
Fuel Injector Replacement / Fuel Injector ID
Code Data Programming
Important:
The Fuel Injector ID Code Data Programming MUST be
done when the fuel injector is being replaced. The Fuel
Injector ID Code information MUST be recorded before
assembling the cylinder head cover.
Removal Procedure
1. Remove the engine harness, the throttle position
sensor, the EGR valve, the pressure sensor, and
all of the fuel injector connectors.
2. Remove the EGR valve and the EGR adapter.
3. Tape the EGR case holes shut to prevent the entry
of foreign material.
Legend
1. EGR Adapter
2. EGR Valve
4. Remove the sound insulation cover.
5. Remove the head cover.
Legend
1. Sound Insulation Cover (For Europe)
2. Head Cover
6. Loosen the fuel injector terminal nuts.
7. Loosen the fuel injector harness bracket bolts.
Remove the inside connector and the harness
bracket.
8. Remove the fuel injector leak-off pipe.
9. Remove the lower cover.
N6A6523E
N6A6523E
N6A6368E
1
2
N6A6027E
Engine Control System (4HK1) 6E-339
Legend
1. Harness Bracket
2. Harness Connector
3. Fuel Injector Terminal
4. Fuel Leak-Off Pipe
10. Remove the fuel injection pipe clips and the
injection pipes.
Legend
1. Fuel Injection Pipe
2. Pipe Clip
11. Loosen the fuel injector clamp fixing bolts and
remove the fuel injectors.
If the fuel injectors are difficult to remove, use the fuel
injector remover. Install the fuel injector remover to the
leak-off pipe attachment part on the fuel injector. Use a
sliding hammer to force the fuel injector clamp off the
fuel injector.
Caution:
Do not remove the fuel injector sleeve.
Special tools
Fuel injector remover: 5-8840-2826-0 (EN-46720)
Sliding hammer: 5-8840-0019-0 (J-23907)
Legend
1. Sliding Hammer
2. Remover
3. Fuel Injector Assembly
12. Mark each fuel injector with the number of the
cylinder from which it was removed. Store the fuel
injectors in a safe place. Position the fuel injector
so that the nozzle is protected.
Caution:
• Do not tamper with the electromagnetic portion of
the fuel injector. Reduced electromagnetic function
will result in injector failure.
N6A6124E
N6A6128E
N6A6129E
6E-340 Engine Control System (4HK1)
Recording from the each fuel injector ID plate
Record 24 figures of each fuel injector ID plate. The
correct order for the fuel injector ID code for the
following illustration is as follows:
56 00 D1 CA 00 00 EC 00 23 14 21 B7
Legend
1. Fuel Injector ID Plate
2. Fuel Injector ID Code
3. Fuel Injector
Installation Procedure
Important:
Install each of the fuel injectors on its original position.
(the cylinder from which it was removed)
1. Install a new gasket and O-ring to each of the fuel
injector clamps. Refer to the illustration.
Legend
1. Gasket
2. Fuel Injector
3. Bolt
4. Fuel Injector Clamp
2. Apply molybdenum to the threads and seating
surfaces of the clamp bolts.
3. Install the fuel injector clamps to the cylinder head.
4. Temporarily tighten the clamp bolts.
5. Apply a thin coat of engine oil to the outer surface
of the fuel injector side sleeve nuts.
6. Install the fuel injection pipes to the position shown
in the illustration.
7. Use a spanner to carefully the sleeve nuts until the
fuel injection pipes contact the fuel injector and
common rail.
8. Tighten the fuel injection pipe clips to the specified
torque.
Tighten:
Clips to 6 N
⋅m (0.6 kg⋅m / 52 lb⋅in)
D1CA
EC00
2100
B7
5600
0000
2314
0000
1
2
3
N6A6524E
N6A6370E
Engine Control System (4HK1) 6E-341
Legend
1. Fuel Injection Pipe
2. Pipe Clip
9. Final tighten the injection clamp bolts to the
specified torque.
Tighten:
Bolts to 30 N
⋅m (3.1 kg⋅m / 22 lb⋅ft)
10. Tighten the injection pipes to the specified torque.
Tighten:
Injection pipes to 44 N
⋅m (4.5 kg⋅m / 33 lb⋅ft)
Legend
1. Clamp Bolt
2. Sleeve Nut
11. Install the nozzle leak off pipes together with the
new gaskets. Tighten the pipes to the specified
torque.
Tighten:
Pipes to 12 N
⋅m (1.2 kg⋅m / 104 lb⋅in)
12. Install the fuel injector harness connectors. Work
from the inside out.
13. Install the harness bracket and tighten the bolts to
the specified torque.
Tighten:
Bolts to 48 N
⋅m (4.9 kg⋅m / 35 lb⋅ft)
N6A6128E
N6A6179E
N6A6181E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст