Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Service manual — part 2058
3C-36 FRONT SUSPENSION
Important Operations
1. Bushing ; Front Side
Remover and Installer : 5-8840-2123-0
(J-36833)
2. Bushing ; Rear Side
Remove and Installer : 5-8840-2124-0
(J-36834)
4. Torsion Bar Arm
Torsion Bar Arm Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
115.7
±
9.8 (11.8
±
1.0/85.3
±
7.2)
6. 8. Nut and Washer
Tighten Lower Link Nut finger-tight.
Perform the secure tightening after adjusting buffer clearance.
9. Lower End
Lower End Bolt Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
103.0
±
9.8 (10.5
±
1.0/75.9
±
7.2)
11.Bushing
Remover and Installer : 5-8840-0256-0
(J-29755)
Apply a suitable socket to (*) portion.
FRONT SUSPENSION 3C-37
13.Nut
Tighten fulcrum pin nut finger-tight.
Perform the secure tightening after adjusting buffer clearance.
14.Upper Link Assembly
Install the smaller clearance A outside and larger clearance B
inside of vehicle.
15.Caster Shims
Caster angle
Short Wheel Base
Long Wheel Base
1
°
55'
±
45'
2
°
10'
±
45'
Note :
No more than 35' side to side variation.
16.Camber Shims
Camber angle
30'
±
60'
Note :
No more than 45' side to side variation.
17.Bolt and Plate
Fulcrum Pin Bolt Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
152.0
±
14.7 (15.5
±
1.5/112.1
±
10.8)
Apply oil to the thread.
19.Upper End
Upper End Bolt Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
32.4
±
2.9 (3.3
±
0.3/23.9
±
2.2)
3C-38 FRONT SUSPENSION
20.Needle Bearing (4
××××
4 model)
Installer : 5-8840-2128-0
(J-36838)
Grip : 5-8840-0007-0
(J-8092)
Before installation, apply the appropriate amount of specified
grease (Besco L2 or equivalent) to the bearing (Approx. 15g).
22.Oil Seal (4
××××
4 model)
Installer : 5-8840-2127-0
(J-36837)
Grip : 5-8840-0007-0
(J-8092)
•
Insert the thrust washer into the knuckle.
•
After fitting the oil seal to the setting tool; installer, drive it to
the knuckle using a hammer or bench press until the tool
front face contacts with the thrust washer.
•
Apply the specified grease to the thrust washer, and install
after turning the place where there is a chamfer to the
spindle.
•
Use a new oil seal, and apply the specified grease (Besco
L2 or equivalent) to the place surrounded by the lip (Approx.
15g).
24.25. Nut and Cotter Pin
Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
Upper Link End
98.1
±
9.8 (10.0
±
1.0/72.3
±
7.2)
Lower Link End
127.5
±
9.8 (13.0
±
1.0/94.0
±
7.2)
Track Rod End
107.9
±
9.8 (11.0
±
1.0/79.6
±
7.2)
Fasten the bushing nut and keep the buffer clearance as
shown on the left diagram.
T = 15 mm (0.59 in)
FRONT SUSPENSION 3C-39
Nut and Washer
Front Lower Link Nut Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
156.9
±
19.6 (16.0
±
2.0/115.7
±
14.5)
Apply oil to the thread.
Nut and Washer
Rear Lower Link Nut Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
196.1
±
19.6 (20.0
±
2.0/144.7
±
14.5)
Apply oil to the thread.
Nut
Fulcrum Pin Nut Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
152.0
±
14.7 (11.0
±
1.5/112.1
±
10.8)
Apply oil to the thread.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст