Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Service manual — part 1996
STEERING 3B-63
DISASSEMBLY AND REASSEMBLY (4J Series Engine Model)
Disassembly Steps
1. Bolt
2. Pipe, suction
3. O-ring
4. O-ring
5. O-ring
6. Connector
7. O-ring
8. Valve
9. Retaining ring
10. Filter
11. Spring
12. Retaining ring
13. Shaft assembly
14. Bearing
15. Shaft
16. Retaining ring
17. Oil seal
18. Bolt
19. Rear housing assembly and pump
cartridge
20. Gasket
21. O-ring
22. O-ring
23. Front housing
24. Pressure plate
25. Rotor and vane
26. Cam
27. Pin
28. Rear housing
Reassembly Steps
28. Rear housing
27. Pin
26. Cam
25. Rotor and vane
24. Pressure plate
23. Front housing
22. O-ring
21. O-ring
20. Gasket
19. Rear housing assembly and pump
cartridge
18. Bolt
17. Oil seal
16. Retaining ring
15. Shaft
14. Bearing
13. Shaft assembly
12. Retaining ring
11. Spring
10. Filter
9. Retaining ring
8. Valve
7. O-ring
6. Connector
5. O-ring
4. O-ring
3. O-ring
2. Pipe
1. Bolt
3B-64 STEERING
DISASSEMBLY
Preparation:
Clean oil pump with solvent (its plug discharge and suction port
to prevent the entry of solvent). Be careful not to expose the oil
seal of shaft assembly to solvent.
1. Bolt
2. Pipe, Suction
3. O-ring
4. O-ring
5. O-ring
6. Connector
7. O-ring
8. Valve
9. Retaining Ring
10. Filter
11. Spring
12. Retaining Ring
13. Shaft Assembly
14. Bearing
15. Shaft
16. Retaining Ring
17. Oil Seal
CAUTION:
When removing the oil seal, be careful not to damage the
housing.
18. Bolt
19. Rear Housing Assembly and Pump Cartridge
20. Gasket
21. O-ring
22. O-ring
23. Front Housing
24. Pressure Plate
25. Rotor and Vane
26. Cam
27. Pin
28. Rear Housing
STEERING 3B-65
REASSEMBLY
28. Rear Housing
27. Pin
26. Cam
25. Rotor and Vane
Install the rotor with its punch mark facing the front
housing.
Install the vane with curved face in contact with the inner
wall of the cam.
24. Pressure Plate
CAUTION:
When install pressure plate, be careful not to damage its
inner surface. Damaged pressure plate may cause poor
pump performance, pump seizure or oil leakage.
23. Front Housing
22. O-ring
Be sure to discard used parts, and always used new parts
for installation.
21. O-ring
Be sure to discard used parts, and always used new parts
for installation.
20. Gasket
Be sure to discard used parts, and always used new parts
for installation.
19. Rear Housing Assembly and Pump Cartridge
18. Bolt
Rear Housing Bolt Torque
N
⋅m (kgf⋅m / lb⋅ft)
54 (5.5 / 40)
17. Oil Seal
Be sure to discard used parts, and always used new parts
for installation.
3B-66 STEERING
CAUTION:
When installing the oil seal, be careful not to damage the
oil seal contacting surface of the housing.
16. Retaining Ring
15. Shaft
14. Bearing
13. Shaft Assembly
12. Retaining Ring
11. Spring
10. Filter
9. Retaining Ring
8. Valve
7. O-ring
Be sure to discard used parts, and always used new parts
for installation.
6. Connector
Connector Torque
N
⋅m (kgf⋅m / lb⋅ft)
54 (5.5 / 40)
5. O-ring
Be sure to discard used parts, and always used new parts
for installation.
4. O-ring
Be sure to discard used parts, and always used new parts
for installation.
3. O-ring
Be sure to discard used parts, and always used new parts
for installation.
2. Pipe, Suction
1. Bolt
Suction Pipe Bolt Torque
N
⋅m (kgf⋅m / lb⋅ft)
21 (2.1 / 15)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст