Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Service manual — part 1704
ENGINE FUEL 6C-7
Fuel Filter
Fuel Filter and Associated Parts
(2.2L & 2.0L Models)
(2.4L Model)
Legend
1 Fuel Hose
2 Fuel Filter
3 Fixing bolt
Legend
1 Fuel Hose
2 Quick Connector
3 Fuel Filter
Removal
CAUTION: When repair to the fuel system has been
completed, start engine and check the fuel system for
loose connections or leakage. For the fuel system
diagnosis, see Section "Driveability and Emissions".
(2.2L & 2.0L)
1. Disconnect battery ground cable.
2. Remove fuel filler cap.
3. Loosen the fixing bolt and disconnect fuel hoses (1).
4. Remove fuel filter (2).
(2.4L)
1. Disconnect battery ground cable.
2. Disconnect the quick connector from the fuel filter.
3. Pull off fuel filter from the holder to side member side.
4. Remove the fuel filter.
6C-8 ENGINE FUEL
Inspection
1. Replace the fuel filter if the fuel leaks from fuel filter body or
if the fuel filter body itself is damaged.
2. Replace the filter if it is clogged with dirt or sediment.
3. Check the drain and if it is clogged with dust, clean it out
with air.
Installation
(2.2L & 2.0L)
1. Install the fuel filter in the proper direction.
2. Install fuel filter holder fixing bolt.
3. Connect fuel hoses on engine side and fuel tank side.
4. Install fuel filler cap
5. Connect the battery ground cable.
(2.4L)
1. Install the fuel filter.
2. Install the quick connectors.
3. Connect the battery ground cable.
Inspection
After installation, start engine and check for fuel leakage.
In-Tank Fuel Filter
The filter is located on the lower end of the fuel pickup tube in
the fuel tank. It prevents dirt from entering the fuel pipe and
also stops water unless the filter is completely submerged in
the water. It is a self cleaning type, not requiring scheduled
maintenance. Excess water and sediment in the tank restricts
fuel supply to the engine, resulting in engine stop. In such a
case, the tank must be cleaned throughly.
ENGINE FUEL 6C-9
Fuel Pump
Fuel Pump and Associated Parts
Legend
1 Fuel Pump and Sender Assembly
2 Fuel Tank Assembly
Legend
1 Fuel Feed Port
2 Fuel Return Port
3 Fuel Emission Port
4 Fuel Pump and Sender Assembly
5 Connector ; Fuel Feed Pump & Sender
6 Fuel Tube / Quick Connector
7 Retainer (Fuel Pump Lock)
8 Seal ; Fuel Pump
9 Fuel Tank Assembly
(2.2L & 2.0L Models)
(2.4L Model)
6C-10 ENGINE FUEL
Removal
CAUTION: When repair to the fuel system has been
completed, start engine and check the fuel system for
loose connection or leakage. For the fuel system
diagnosis, see Section “Driceability and Emission”.
1. Disconnect battery ground cable.
2. Loosen fuel filler cap.
3. Support underneath of the fuel tank assembly (2) with a
lifter.
4. Remove fuel tank assembly (2). Refer to “Fuel Tank
Removal” in this section.
5. Remove fuel pump and sender (FPAS) assembly (1) fixing
snapring and remove the FPAS assembly.
NOTE:
• After removing pump assembly (1), cover fuel tank to
prevent any dust entering.
• Remove the fuel pump lock.
Installation
1. Install FPAS assembly (1).
2. Install fuel tank assembly (2). Refer to “Fuel Tank
Installation”.
3. Fill the tank with fuel and tighten fuel filler cap.
4. Connect battery ground cable.
Fuel Tube/Quick-Connector Fittings
Precautions
• Do not light a match or create a flame.
• Keep flames away from your work area to prevent
flammable materials from catching fire.
• Disconnect battery ground cable to prevent electrical shorts.
• Pre-treat piping system or associated parts from thermal
damage or from spattering when welding or similar heat-
generating work.
Legend
(1) O-ring
(2) Port
(3) Connector
(4) Plastic Tube
Cautions During Work
Do not expose the assembly to battery electrolyte or do not
wipe the assembly with a cloth used to wipe off spilt battery
electrolyte.
Piping that has been splattered with battery electrolyte or
battery electrolyte soaked cloth that was wiped on the piping
cannot be used.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст