Isuzu KB P190. Service manual — part 945
Automatic Transmission – 4L60E – General Information
Page 7C1–20
8 Special
Tools
The following pages list and illustrate the special service tools required. The tools are classified into the following
categories:
Mandatory:
When required to perform routine maintenance operations and adjustments, or are required to carry out
fault diagnosis procedures.
Desirable:
These tools should be considered for purchase since their use will greatly facilitate performing designated
tasks and permit achievement of standard times.
Unique:
These tools are those that must be employed when overhauling major assemblies or performing relatively
large tasks.
Available:
Are those tools that are of a general nature for which commercially available equivalents exist, or tools
which have had previous application.
Unless otherwise specified, all tools are available from:
SPX Australia PTY. LTD.
Service Solutions
28 Clayton Road
Notting Hill, Victoria, 3168
Telephone: (03) 9544 6222
Facsimile: (03) 9544 5222
Tool Number
Illustration
Description
Tool Classification
700-4208
Pass-Thru Connector Remover
Used to release the four locking tangs
on the Pass-Thru connector from the
transmission case.
Previously released
Desirable
J6125-1B
Slide Hammer
Used for a number of bush removal
operations.
Previously released
Unique
J8092
Driver Handle
Used for a number of bush installation
operations.
Previously released
Unique
J8433
Puller
Used with J21427-01 to remove the
output speed sensor ring from the
main shaft.
Previously released
Unique
J8763-02
Holding Fixture
Used in conjunction with holding
fixture base J3289-20 to hold
automatic transmission.
Previously released.
Unique
Automatic Transmission – 4L60E – General Information
Page 7C1–21
J21368
Oil Pump Alignment Band
Used to align the two oil pump
sections before tightening the
securing bolts.
Previously released
Unique
J21426
Rear Seal Installer
Used to install the extension housing
oil seal.
Previously released
Unique
J21427-01
Puller Adaptor
Used with J8433 to remove the output
speed sensor ring from the main
shaft.
Previously released
Unique
J21465-2
Installer
Used with driver J8092 to install the
front stator shaft bush.
Previously released
Unique
J21465-15
Remover
Used in conjunction with slide
hammer J6125-1B to remove the
stator shaft front bushing.
Previously released
Unique
J23062-14
Bush Remover
Used in conjunction with driver handle
J8092.
Previously released
Unique
J23327-1
Clutch Spring Compressor
Needed to compress the clutch,
before dismantling.
Plate J42628 is also required.
Previously released
Unique
J23907
Slide Hammer
Used with J29369-2 to remove the
reaction carrier shaft bushes.
Previously released
Unique
J25016
Oil Pump Seal Installer
Used to install the oil pump oil seal.
Previously released
Unique
Automatic Transmission – 4L60E – General Information
Page 7C1–22
J25018-A
Clutch Spring Compressor Adaptor
Used with compressor J23327 to
compress the reverse input clutch
during disassembly.
Previously released
Unique
J25019-4
Bush Installer
Used in conjunction with J8092
Installer Handle.
Previously Released
Unique
J25019-9
Bush Installer
Used in conjunction with driver handle
J8092.
Previously released
Unique
J25019-14
Bush Remover
Used with slide hammer J6125-1B.
Previously released
Unique
J25019-16
Bush Remover
Used with slide hammer J6125-1B.
Previously released
Unique
J29369-2
Universal Bush Remover
Used with slide hammer J23907.
Previously released
Unique
J29882
Inner Overrun Clutch Seal
Protector
Used to protect the inner, overrun
clutch piston seal from damage during
installation.
Previously released
Unique
J29883
Inner Forward Clutch Seal
Protector
Used to protect the inner, forward
clutch piston seal from damage during
installation.
Previously released
Unique
J33037
2 – 4 Band Apply Pin Tool
Used to check the selective apply pin
length.
Previously released
Unique
Automatic Transmission – 4L60E – General Information
Page 7C1–23
J34196-B
Bush Remover/Installer Set
Used for various applications,
described in the text.
Previously released
Unique
J34627
Snap Ring Pliers
Specific purpose is to assist in the
removal/replacement of the output
shaft snap ring.
Previously released
Unique
J35138
Torque Converter End Play
To be used in conjunction with
commercially available magnetic
stand and dial indicator.
Previously released
Unique
J36352
Speed Sensor Installer &
Gauging Tool
Needed to correctly install the output
speed sensor ring to the main shaft.
Comprises sleeve, J36352-6 and C-
washer J36352-4.
Previously released
Unique
J36418-B
Turbine Shaft Seal Installer &
Resizer
Used to install and re-size the turbine
shaft seal. Comprises J36418-1B
installer and J36418-2A resizer.
Previously released
Unique
J37789-A
Oil Pump Remover
Used with J39119 to remove the oil
pump assembly.
Previously released
Unique
J38735-3
Stator Shaft Sealing Ring Installer
Used with J39855-1 to install the
stator shaft seal.
Previously released
Unique
J39119
Oil Pump Remover Adaptor
Used with J37789-A to remove the oil
pump assembly.
Previously released
Unique
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст